User manual BLAUPUNKT MIAMI BEACH CD51

[. . . ] Radio / CD Miami Beach CD51 Tampa Bay CD51 Operating instructions Open here Ouvrir s. v. p. Por favor, abrir Favor abrir 2 1 2 3 4 16 15 5 6 14 7 13 12 11 10 8 9 3 PORTUGUÊS ESPAÑOL FRANÇAIS ENGLISH CONTROLS 1 2 3 4 5 6 7 8 9 : button ­ to unlock the removable control panel (release panel) Volume control Button ­ switches the unit on/off, volume mute FM button ­ selects the radio mode source, selects the FM memory levels AM button ­ selects the radio mode source, selects the AM frequency range Display button ­ displays the time, DIS ­ changes the display content MENU button ­ opens the basic settings menu button ­ opens the fliprelease panel Arrow buttons ; < = > ?@ OK button ­ confirms menu entries and starts the scan function X-BASS button ­ to set the X-Bass feature AUDIO button (audio) ­ adjusts the bass, treble, balance and fader Keys 1 - 6 TS button ­ starts the Travelstore function CD·C button ­ to switch between CD, CD changer (if connected) and AUX sources 4 TABLE OF CONTENTS Road safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Keep pressing the or button : until "MUTE LEVEL" appears in the display. When you have finished making your changes, Set the power-on volume using the and buttons :. If you change the setting to "0", the power-on volume will be the same as the volume level that was set before the unit was last switched off. Note: To protect your hearing, the poweron volume is limited to a value of "38". If the volume level was higher when the unit was switched off, the volume will be reset to "38" when the unit is switched on again. When you have finished making your changes, Set the mute level using the press the MENU button 8 or OK ; twice. Telephone audio / navigation audio If your car radio is connected to a mobile telephone or a navigation system, the unit's volume will be muted as soon as you "pick up" the telephone or as soon as a navigation announcement is made. The caller or voice output will then be heard over the car radio loudspeakers. In order for this to work, the mobile telephone or navigation system must be connected to the car radio in the manner described in the installation instructions. press the MENU button 8 or OK ; twice. 9 ADJUSTING THE VOLUME You can find out from your Blaupunkt dealer which navigation systems can be used with your car radio. You can set the volume level at which telephone calls and the navigation voice output will first be heard. Keep pressing the or button : until "TEL/NAVI VOL" appears in the display. Set the required volume using the and buttons :. When you have finished making your changes, and buttons :. "0" means beep off, "9" means maximum beep volume. When you have finished making your changes, Set the volume using the press the MENU button 8 or OK ;. press the MENU button 8 or OK ; twice. Note: Using the volume control 2, you can directly adjust the volume of telephone calls and navigation voice output (whilst they are being heard). Setting the volume of the confirmation beep For some functions you will hear a confirmation beep if you keep a button pressed for longer than two seconds. For instance, after storing a radio station to a station button you will hear a confirmation beep. You can set the volume of this beep. Press the MENU button 8. Keep pressing the or button : until "BEEP" appears in the display. 10 RADIO MODE Switching to radio mode If you are in CD, CD changer or AUX mode, ENGLISH PORTUGUÊS ESPAÑOL FRANÇAIS Radio mode press the FM 4 / AM 5 button or Setting the sensitivity for station seek tuning You can configure the radio to only tune into stations with a strong reception or to also tune into those with a weak reception. keep pressing the CD·C button @ until "RADIO" appears in the display. Press the MENU button 8. Keep pressing the or button : until "SENS HI" or "SENS LO" appears in the display. "SENS HI" means that the tuner is highly sensitive. "SENS LO" means it is set to the lowest sensitivity setting. If "SENS LO" is selected, "lo" lights up in the display. Selecting the frequency range / memory This unit can receive programmes broadcast over the FM and AM frequency ranges. [. . . ] Setting the front/back volume distribution (fader) To set the front/back volume distribution (fader), press the AUDIO button =. "BASS" appears in the display. Keep pressing the button : until "TREBLE" appears in the display. Keep pressing the Press the Press the or button : to adjust the treble. When you have finished making your changes, button : until "FADER" appears in the display. press the AUDIO button =. or button : to adjust the fader (front/back). When you have finished making your changes, press the AUDIO button =. 19 X-BASS X-BASS The X-BASS feature can be used to boost the bass at low volume levels. SPECTROMETER Setting the spectrometer The spectrometer (level display) briefly provides a symbolic display of the volume and the audio control settings whilst you are adjusting them. [. . . ]