User manual BLAUPUNKT ORLANDO CM127

[. . . ] FCC Warning The equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications. However, there is no guarantee that radio interference will not occur in particular installation. [. . . ] size M5x8 to dashboard/center console max. size M5x8 Bracket Support 2 NISSAN max. size M5x8 to dashboard/center console max. size M5x8 Bracket Support 9 Maintenance Removing the Unit Use the Release Keys as shown below. Keep them in a safe place in case you need them in the future. Fuse Replacement When replacing the fuse, be sure to use one with the correct amperage, which will be stated on the fuse case. Never use a fuse that has a stated amperage exceeding the one supplied for this unit, as this could cause malfunction and serious damage to the unit. 10 Specifications Audio Power Specifications Power Output and Total Harmonic Distortion: 13 watts per channel minimum continuous average output into 4 ohms, 4 channels driven, from 30-15, 000 Hz with no more than 1% total harmonic distortion. Other Specifications Tuner FM Tuning Range: Intermediate Frequency: FM Mono Sensitivity: Seek lo sensitivity: Seek sensitivity Selectivity: Signal-to-Noise Ratio: Harmonic distortion at 1 kHz: Separation: Frequency Response: AM Tuning Range: Seek lo sensitivity Seek sensitivity: Intermediate Frequency: Signal-to-Noise Ratio: Frequency Response: 87. 5 - 107. 9 MHz 10. 7 MHz 13 dBf 51 dBf 31 dBf 80 dB at 400kHz 65 dB (stereo), 70 dB (mono) 0. 7% (stereo), 0. 5% (mono) 30 dB 30-15, 000 Hz ± 3 dB 530 - 1, 710 kHz 50 dBµV 25 dBµV 450 kHz 50 dB 30-5, 000 Hz + 3dB Audio Speaker Impedance: Maximum Amp Power: RMS Power: Bass Control: Treble Control: Loud: Preamp Output: 4-8 ohms 4 X 30 Watts (at 4 ohms) 4 X 13 Watts (at 4 ohms) <1% THD ± 10 dB @ 100 Hz ± 10 dB @ 10 kHz + 8 dB @ 60 Hz & + 2 dB @ 8 kHz 4-Channel, Low-Impendance (100 ) Preamplifier Over 3 Volts of Distortion-Free Preamp Output Cassette Signal-to-Noise Ratio: with Dolby B Noise Reduction: Tape Wow and Flutter: Tape Frequency Response: 55 dB 65 dB 0. 10% dB 30-18, 000 Hz + 3 dB 180 x 52 x 155 mm, 7 x 3 x 6 1/8 in. 1. 4 kg (3. 0 lb. ) 12 V DC car battery (11-16 V DC allowable) 15°F to 120°F, ­10°C to 50°C · Unit · Faceplate · Wire Harness, including 2-Channel RCA Preamp Output Harness · DIN Sleeve · Mounting Hardware · Owner's Manual in English, French, Spanish and Portuguese · 4-Channel Preamp Output Harness (Part No. 8634494218) · CDC-A05 or CDC-A071 CD Changers 11 General Dimensions (w/o projecting parts/controls): Mass: Power Requirement (neg. grnd. ): Operating Temperature: Supplied Accessories: Optional Accessories: Design and specifications subject to change without notice. Location of Controls 1. LD (Loudness)/ SENS (Tuning Sensitivity) 8. + Button Volume + Bass + Treble + Balance Left Fade to Front 13. - Button Volume Bass Treble - 14. 15. 16. 22. Balance Right Fade to Rear /\ Button Seek and Manual Tuning CD Track Up Audible CD Cue Clock Hours V Button Seek and Manual Tuning CD Track Down Audible CD Review Clock Minutes FM/AM Presets Disc Select CD Pause CD Repeat CD Mix Dolby B Noise Reduction Display Instructions -- General Operation See Traffic Safety & Precautions on page 4. "Press" means a momentary press of less than 1/2 second. All presses requiring more than 1/2 second are followed by beep. "Time Out" When additional button presses are anticipated to complete a procedure, the unit will automatically exit the procedure after 4 seconds of inactivity. 12 Ignition-Off Clock Recall Any button press while ignition off displays time for about 8 seconds. Ignition-On Unit lights up and clock is displayed. Release for Detachable Faceplate Push REL to detach face. Already-inserted cassette remains in unit. Current settings and source mode are stored. If power was not switched off before face removed, unit will automatically poweron when face is reattached. Power (PWR) On/Off When ignition on, press PWR or insert a disc to turn unit on. Last-used source becomes active, unless unit is turned on by inserting tape, in which case tape player becomes active. [. . . ] Unit continuously scans until user stops scan by pressing SCA, another playback control or SRC. Track Scan deactivates any previously-active MIX or RPT modes. Disc Scan Press and hold SCA for more than 2 seconds to start Disc Scan. Disc Numbers blink during scanning operation. [. . . ]