User manual BLAUPUNKT RPC 4000

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. OWNER'S RECORD The model and warranty numbers are located on the top of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you Call upon your Blaupunkt dealer regarding this product. [. . . ] Connect the black (power ground) lead to a grounded metal part on the vehicle. We recommend grounding all audio system black ground leads (head unit, CD changer, etc. ) to a common grounding point, preferably a non-painted surface under the instrument panel. Connect the yellow (constant power) input lead to a source of constant battery power, preferably a terminal to an appropriate slot in the fuse box. Connect the red (turn-on power) input lead only after the other leads are connected. Be sure to connect the red lead to a positive (+) 12 Volt power terminal that is energized only when the ignition key is set to the on position or accessory position. 7 Cover the ends of any unused leads with electrical tape. This will prevent them from touching the vehicle or each other and causing a short-circuit and damage to the radio or vehicle, 6 Reconnect the vehicle's battery 9 Venfy that no fuses have blown 10 Plug the harness into the ""0 11 Attach the faceplate and test the "not Once the connections have been successfully made, you can begin to install the unit 5. 6. l SPEAKER CONNECTfONS You can connect a speaker (regular, co-axial or hi-axial speakers or component speaker system, all hereafter referred to simply as "speaker') to each of the units' four pairs of speaker leads. Connecting the Speaker Leads To prevent short circuits or serious damage to the unit and/or speakers: l Connect the speaker leads only as indicated in the wiring diagram. l Only use speakers that have impedance ratings of 4 ohms or higher and have power-handling capabilities greater than the head unit's stated power level. l The units internnl amplifier is designed to handle a 4-ohm load on each pair of speaker leads. l DON'T connect two speakers to a single pair of speaker leads ("in parallel") unless both speakers each have at least 6 ohms impedance. Signal-to-Noise Ratio: 45 dB Mass: Approx. 1. 4 kg (3. 0 lb. ) Design and specifications subject lo change withouf notice. gmd. ): 12 V DC car battery Operating Temperature: 15°F to 12O'F. -10°C to 50°C l Untt l Faceolate Supplied Accessories: r l Mounting Hardware * DIN Sleeve l Owner's Manual In English, French, Spanish and Portuguese INSTRUCTIONS - GENERAL OPERATION "Press" means momenlaly press of less than l/Z second Turning Unit On Vehicle lgnlbon must be on To turn unit on. Turning Unit Off Press the PWR Button to turn the u", t off Volume Press + or-to quickly increase or decrease the volume to the desired level. The volume level is indicated in lhe Display Window. To make a fine adjustments to the volume level. press the other part of the button before the volume level disappears from the display. You can then gradually adjust the volume I" either direction, making precise adjustment easy. Adjustable Turn-O" Volume First adfust the volume to the (maxtmum) volume level dewed when the unit IS turned on Press and hold the PWR Button for more than two seconds The untt turns off and the turn-on volume level IS memowed When the unit 8s turned cm. the volume wll be at the mamonzed Iavel. [. . . ] * Manual: To reverse tape direction during playback, press the PROG (Program) Buttons. The change in direction and in tape program will be confirmed in the Display. Fast Winding of Tape No matter which side of the lapa that is playing: . The direction arrow will blink to confirm the fast-fonvardmg. [. . . ]