User manual BLAUPUNKT TP DX-N SIL. IBERIA

[. . . ] 18 Installing the navigation unit . . . . . . . . . . . . . . 5 Where to install the navigation unit . . . . 5 Positive connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Negative connection . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Connecting the back-up lights signal wire . . . . . . . . . . . . . . . . . 7 Video input assignment . . . . . . 8 System test after installation . . . . . . . . . . . . . . . . . . 8 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Calibrating the Gala curve . . . . . . . . . . . . . . . . . [. . . ] page 7 Installing the speedometer signal wire . . . . . . . . . . . . . page 7 Installing the back-up lights signal wire . . . . . . . . . . . page 7 Notes on how the system functions The TravelPilot is equipped with an automatic calibration feature which is required to determine the current vehicle position. Depending on the GPS reception available, the calibration is completed after the vehicle has been driven approx. Driving along a winding route (in the city), which is indicated on the monitor on a map, accelerates the calibration. The speedometer signal connection in the vehicle allows the system to determine the distance driven. If there is no speedometer signal, it will be necessary to have a route sensor installed by an authorised customer service centre. In this case, you will have to order a sensor kit (route sensor, magnet strips, bracket, plug and installation instructions) from your dealer. Order No. : 7 607 611 093 Installation Installing the navigation unit Where to install the navigation unit Important!Before inserting the TravelPilot, you have to make sure that the gyroscope is positioned horizontally (see Fig. The TravelPilot DX-N can be installed in the car radio compartment in the vehicle (installation depth 218 mm). Before drilling the holes for the mounting screws, make sure that no damage will be done to covered wiring, the petrol tank or fuel lines! Display installation Fig. 3 The display is mounted on the dashboard or console using the enclosed ball-and-socket base. 4 The display is mounted directly on a console (telephone console) with the ball joint. 5 The display is mounted using the swan neck fitting 7 612 001 204 and the ball-and-socket base. To do so, you must disassemble the rear panel of the display. A 10 mm wide hole must be drilled at the mounting position to accommodate the cable. When the cable is installed, you must ensure it will safe from being tugged or stretched or from being exposed to any other loads. Installation Installing the control unit Mount the control unit bracket in a location where the control unit will be easily accessible, e. g. Do not mount the control unit within the inflation range of the airbags (on the driver's side, the passenger side or the side airbags) or where it might strike the head or knees of anyone in the vehicle in the event of an accident!Before drilling the holes for the mounting screws, make sure that no damage will be done to covered wiring, the petrol tank or fuel lines!Make sure that the vehicle operating elements remain easily accessible and are not obstructed in any way (gear stick, hand brake, etc. )!Important: We assume no responsibility for any equipment that is installed incorrectly and the consequences thereof! Connecting the speedometer signal Important: This connection should be made by an authorised customer service centre. [. . . ] Now select the required test using the or button, press the OK button and follow the on-screen instructions. If the test was completed successfully, the menu item will be labelled with a tick. If an error occurs, an appropriate notice will be displayed. Close the service menu by pressing the button. Low = PAL Format / High = NTSC Format E A A A Low = Off / High = On Low = Mirror image / High = Normal image Calibration Calibration After installation, the TravelPilot DX-N must be calibrated. [. . . ]