User manual BLAUPUNKT TP DX-V BLACK D

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to contact the dealer or an experienced Radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Owner's Record The model and warranty numbers are located on the top of the unit. Record the warranty (serial) number in the space provided below. Refer to these numbers whenever you call upon your Blaupunkt dealer regarding this product. [. . . ] See* below. E N G L I S H * A B 5 Electrical Connections and Installation @/<?#&*>@!To avoid the aggravation of costly mistakes and serious damage that could make you feel this way, please carefully read all of the instructions before you begin. You'll be glad you did! GENERAL RECOMMENDATIONS · If you're not confident that you can install the unit correctly, have it installed by a qualified Blaupunkt installation technician. · Use this unit only with negative ground 12 Volt (11-16 Volt) direct current (DC). · Be sure to detach the faceplate before you start to connect or install the unit. · Don't assume that a seemingly matching wire harness in the vehicle has leads that match the leads of the unit's wire harness. · We recommend making and testing all electrical connections before installing the unit. Connect the leads (wires) according to instructions and diagram below. ELECTRICAL CONNECTION INSTRUCTIONS 1. Disconnect the vehicle battery's negative terminal before making connections. Connect the speakers and/or external amplifiers (if you have any) following the guidelines in the SPEAKER CONNECTION section below. Connect the blue (trigger output) lead to the antenna motor trigger switch input terminal or amplifier trigger switch input terminal (if you have either if these items). · DON'T connect any active speakers (with built-in amplifiers) to the speaker leads unless their owner's manuals specifically state that this is O. K. · Cover the ends of any unused leads with electrical tape. This will prevent them from touching the vehicle or each other and causing a short-circuit and damage to the radio or vehicle. Connecting the Pre-Amp Outputs to External Amplifier(s) To prevent short circuits or serious damage to the receiver, amplifier, and/or speakers: · Follow the amplifier's instructions on how to connect the unit's preamp outputs to the amplifier(s) and connect the speaker(s) directly to the amplifier. AUXILIARY FUSE 5A * * * Harness has single blue lead that can be used for either antenna motor trigger switch or amp trigger or spliced for use with both. (See note 3. ) 7 Installation Recommendations · Carefully choose the mounting location so that the unit won't interfere with normal driving. · Avoid mounting locations where the unit would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would subject to dust, dirt or excessive vibration. · The illustration below shows a typical installation, however, you may need to adjust the installation, depending on the unit. If you have questions or need additional installation hardware, consult your Blaupunkt dealer. · Make sure the unit is firmly anchored (preferably at both front and back) and does not vibrate. Mounting Hardware (1) Sleeve (2) Mounting Strap and Screw (3) Release Keys Mounting The Unit in Most Dashboards 1 Install the Sleeve (1) in the dashboard. 1. 4 kg (3. 0 lb. ) 12 V DC car battery (11-16 V DC allowable) 15°F to 120°F, ­10°C to 50°C · Unit · Faceplate · Wire Harness, including 2-channel RCA Preamp Output · DIN Sleeve · Mounting Hardware · Owner's Manual in English, French, Spanish and Portuguese General Dimensions (w/o projecting parts/controls): Mass: Power Requirement (neg. grnd. ): Operating Temperature: Supplied Accessories: Design and specifications subject to change without notice. 11 Location of Controls 1. [. . . ] Pressing any tuning-related button during Travel Store process cancels search operation. Frequency blinks (along with preset number if appropriate) during scanning. Unit stops at receivable stations for 4 seconds. Unit continuously scans until user stops scan by pressing SCA, another tuning button or SRC. Cassette Tape Player Operation Tape Playback: · Insert cassette into Cassette Door. [. . . ]