User manual BLAUPUNKT TP DX-V NAVI-RECHNER OCD

[. . . ] The navigation equipment is suitable for vehicles with: · 12 V battery power · Negative pole on the vehicle body Contents Safety precautions . . . . . . . . . . . . . . 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation preparations . . . . . . . . . . . . . . . . . . . . 4 Installing the control unit . . . 6 Important installation information for the speedometer signal . . . . . . . . . . . . 6 Connecting the speedometer signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 What's included in the delivery . . . . . . . . . . . . . . . . . . . . 10 Assembly illustrations . . . . . [. . . ] Order No. : 7 607 611 093 Installation Installing the navigation unit Where to install the navigation unit Important!Before inserting the TravelPilot DX-V, you have to make sure that the gyroscope is positioned horizontally (see Fig. The TravelPilot DX-V can be installed in the car radio compartment in the vehicle (installation depth 218 mm). You will need an installation bracket (order no. For vehicles without a DIN compartment, a universal equipment housing has been included (see Fig. Check to see which method of installation is required for the vehicle and, if necessary, use a vehicle-specific installation kit. When selecting an installation location, you must remember that the navigation unit has to be built into the vehicle body. Installation position: right / left slope to the rear min. +100° Positive connection Connect the navigation unit to continuous plus and the positive connection to the ignition. Lay the continuous plus wire (red) to the battery (do not lay the wire directly along any wire harnesses). Connect a fuse holder to protect the positive wire at a maximum of 30 cm from the vehicle battery (if necessary, drill a hole in the splashback and use the necessary wire bushing). Connect the switching plus wire (black) to terminal 15 on the fuse holder (plus is switched by the ignition) behind the fuse. Negative connection Screw the negative wire (brown) directly to the vehicle body. Scratch the contact points on the ground down to the metal and grease it with graphite grease (important for a good ground). Installing the GPS antenna Install the antenna according to the enclosed instructions. If the GPS antenna is installed inside the vehicle, there is no guarantee that the system will function properly. A fan has been built into the back of the unit to cool it when it overheats. To allow for sufficient air circulation, make sure that the air vents are not blocked. Use only the hole strips to attach the unit to the mounting bolt. Make sure that there is enough room to insert and remove the navigation CD. 5 Allgemeines Kurzanlei- Zieleingabe Touren Zielspeicher Einstellun- Anhang Installation Installing the display Safety instructions The display support must never be greased or lubricated with oil. The monitor cable must be laid so that it is not subjected to any tensile strains or other loads. Do not mount the monitor within the inflation range of the airbags (on the driver's side, the passenger side or the side airbags) or where it might strike the head or knees of anyone in the vehicle in the event of an accident!Before drilling the holes for the mounting screws and wiring, make sure that no damage will be done to covered wiring, the petrol tank or fuel lines!Attach the display support to the display (Fig. Mount the display together with its support onto the dashboard or console (Fig. [. . . ] Now select the required test using the or button, press the OK button and follow the on-screen instructions. If the test was completed successfully, the menu item will be labelled with a tick. If an error occurs, an appropriate notice will be displayed. Close the service menu by pressing the button. 4. [. . . ]