User manual BLAUPUNKT TP E EXACT MP3 R/B TUERK

[. . . ] 21 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Location of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Instructions ­ General Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect the ground lead to a grounded metal part on the vehicle. We recommend grounding all audio system ground leads (head unit, external amplifier, etc. ) to a common grounding point, preferably a non-painted surface under the instrument panel. Connect the battery input lead to a source of constant battery power, preferably a terminal to an appropriate slot in the fuse box. Connect the ignition input lead only after the other leads are connected. Be sure to connect the ignition lead to a positive (+) 12 Volt power terminal that is energized only when the ignition key is set to the on position or accessory position. Cover the ends of any unused leads with electrical tape. This will prevent them from touching the vehicle or each other and causing a short-circuit and damage to the radio or vehicle. Plug the harness into the unit. Electrical Connections 5A Ignition Antenna Ground ­ +12V Battery +12V 21 PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS Electrical Connection Instructions ENGLISH DEUTSCH Electrical Connections Speaker Connections Speaker Connections 5A RR R F LF LR + + + + - RF LF RR LR Attach the faceplate and test the unit. Once the connections have been successfully made, you can begin to mount the unit. 22 Recommendations · The illustration below shows a typical installation, however, you may need to adjust the installation, depending on the unit. If you have questions or need additional installation hardware, consult your Blaupunkt dealer. Make sure the unit is firmly anchored and does not vibrate. · Mounting Hardware Sleeve Release Keys Mounting The Unit in Most Dashboards 1. (If faceplate still attached, display switches to clock. ) Setting the Clock Turn the unit on. Press the CLK Button for four seconds until the clock starts blinking. (The display will change after two seconds. Ignore this and continue to hold for two more seconds. ) Once the clock starts blinking, Press the to set the hour, and press the Button to set the minutes. (To change the minute indicator to the nearest hour (:00), you can press the AUDIO Button. Press the CLK Button again to activate the clock. Changing the Information Displayed You can temporarily change the information shown in your unit's display. You can also select which information has "display priority" and is shown in the display except for moments when adjustments are made. · To change the display priority, press the DISP Button for two seconds. The display priority choices are clock or radio frequency/"TAPE". · To change the display temporarily, press and release the DISP Button to access the desired information. [. . . ] To cancel, press LD again. 28 Last Station Memory Each FM bank and AM band has its own last station memory which holds last-tuned frequency for that band or bank irrespective of whether that frequency is stored into a preset. Selecting Bands Press SRC as needed to access FM1, FM2, FM3/FMT, AM/AMT banks. Seek Tuning Press or to seek next receivable frequency. Tuning stops at frequency that fulfills sensitivity requirements predetermined by sensitivity set through SENS button. [. . . ]