User manual BLAUPUNKT TP RECHNER RNS150 BLACK

[. . . ] Please check the installation conditions in your vehicle and use a vehicle-specific installation kit if necessary. termine which fastener tabs you can bend over with a screwdriver (see Fig. Note: Bend over as many of the fastener tabs as possible. 3. 1 Radio antenna In pre-equipped vehicles (e. g. : VW, Seat, Audi), the antenna gets its power supply via the antenna wire (see the vehicle operating instructions). If you want to replace the OEM radio with a conventional radio, you will have to order an antenna supply diplexer (Order-No. [. . . ] 7 691 290 202) or the adapter cable (Order-No. You will find information on the installation and connection of the antenna in the antenna installation instructions. 5). 4. 3 Installing the TravelPilot Push all of the plugs into the sockets until they lock into place. Now insert the navigation system from the front into the bracket. Apply gentle pressure to both side edges and push it in until the spring locks snap into position on the right and left (you will hear a loud click). When you push in the system, make sure that you do not put any pressure on the display, the knobs or the keys! 3. 2 GPS antenna (satellite navigation) You will find information on how to install the antenna in the enclosed antenna installation instructions. If the GPS antenna is installed inside the vehicle, we cannot guarantee that the system will function correctly. 4. 2 Installing the bracket The bracket included with this TravelPilot allows you to install the system in vehicles with a DIN car radio compartment measuring 182 x 53 x165 mm and an instrument panel which is 1 to 20 mm in the area where the fastener tabs are located, (see Fig. For the installation, you have to push the bracket into the compartment and de- 4. 4 Removing the TravelPilot Insert the handles into the corresponding holes on the left and right side of the front panel and push them in until you hear a loud click (unlocking the side spring locks). Use both handles to carefully pull the TravelPilot out of the compartment. 6 ­10 ° +30 ° Fig. 7 ­10 ° +30 ° O. K. ­10° 2 90° +3 0° Fig. 8 Installation instructions C-1 1 4 3 2 5 6 C-2 7 10 9 12 8 11 C-3 13 16 19 15 18 14 17 20 A B 1 2 3 4 5 6 7 8 Speaker out RR+ Speaker out RRSpeaker out RF+ Speaker out RFSpeaker out LF+ Speaker out LFSpeaker out LR+ Speaker out LR1 2 3 4 5 6 7 8 9 10 D GND -- -- -- -- -- Sensor -- Sensor -- C B A C 9 10 D 5 6 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Gala/Tacho Tel. -Mute (active low) RFLS Permanent +12V Aut. antenna Illumination Ignition Ground 7 1 3 2 4 8 Wheel sensor C3 13 14 15 16 17 18 19 20 CDC Data-IN CDC Data-OUT +12V Permanent +12V switch voltage (max. 300mA) CDC Data-GND CDC AF/AUX-GND CDC AF/AUX- L CDC AF/AUX- R C1 1 2 3 4 5 6 Line Out LR Line Out RR Line Out GND Line Out LF Line Out RF +12V switch voltage (max 150mA) 7 8 9 10 11 12 C2 -- -- -- +12V switched voltage (max. 150mA) Remote Control-In Remote Control-GND Fig. 9 Equalizer Amplifier RC 06 CD changer 259 ENGLISH SVENSKA DANSK Installation instructions Control cable (Power Antenna +) The control cable is the connected positive output for auxiliary components e. g. : power antennas, (maximum load < 150 mA). Do not connect the control cable to terminal 15 (Plus connected) or terminal 30 (continuous plus). 260 12V Relais Wheel sensor (required for vehicles without a speedometer signal only) Plus connection (connected to the ignition) This connection must be made via the ignition (terminal 15, +12V). terminal 15 +12V A 8 604 390 045 Ground Do not connect the ground wire (min. [. . . ] Do not connect the control cable to terminal 15 (Plus connected) or terminal 30 (continuous plus). 260 12V Relais Wheel sensor (required for vehicles without a speedometer signal only) Plus connection (connected to the ignition) This connection must be made via the ignition (terminal 15, +12V). terminal 15 +12V A 8 604 390 045 Ground Do not connect the ground wire (min. cross-section 1. 5 mm2) to the negative terminal of the battery. [. . . ]