User manual BLAUPUNKT TRAVEL PILOT DX-N SIL. I

[. . . ] The TravelPilot can be used in vehicles with: · 12 V battery power · Negative pole on the chassis 2. Connecting the speakers 2. 1 Connecting the speakers to the ISO standard plug In vehicles pre-equipped with passive speakers (with 4-ohm speakers) you can adapt the ISO plug in the vehicle. If necessary, the ISO cable (Order-No. 7 607 647 093) can be used for extra length (see Fig. [. . . ] Power supply 1. 1 Connection to the vehicle ISO standard plug To prevent electrical malfunctions in vehicle ISO plugs, you have to use the universal ISO adapter cable (OrderNo. The following vehicles with ISO standard connections can currently be fitted with the universal ISO adapter cable: Alfa Romeo, Citroen, Fiat, Honda, Lancia, Mercedes, Peugeot, Porsche, Renault, Skoda. ­ ­ ­ ­ Installation instructions 3. Installing the antenna Connect the antenna wiring to the enclosed bracket(see Fig. Installing the TravelPilot 4. 1 Setting the Gyro Important: Before the TravelPilot is inserted, the gyroscope must be put in a horizontal position (see Fig. Important: Installation position of the TravelPilot: right / left: min. +30° The TravelPilot is installed in the standard car radio compartment provided by the manufacturer (see Fig. For vehicles without a DIN compartment, Blaupunkt offers vehicle-specific installation kits for 50/52 mm units for the most popular vehicle models. Please check the installation conditions in your vehicle and use a vehicle-specific installation kit if necessary. termine which fastener tabs you can bend over with a screwdriver (see Fig. Note: Bend over as many of the fastener tabs as possible. 3. 1 Radio antenna In pre-equipped vehicles (e. g. : VW, Seat, Audi), the antenna gets its power supply via the antenna wire (see the vehicle operating instructions). Fig. 5 TravelPilot installation . . . . . . . . . . . . . . . Fig. 6/6a TravelPilot removal . . . . . . . . . . . . . . . . . . . . Fig. 7 Setting the gyroscope . . . . . . . . . . . . . . . . Fig. 8 Connection assignments . . . . . . . . . . . Fig. 9 Connecting the sensors . . . . . . . . . . . . . Fig. 10 4. 5 Connecting the back-up light signal wire The back-up light signal wire connects the system to the vehicle back-up light. Make sure that this connection is charged with 12 volts when the vehicle is reversing. Important: We assume no liability for faulty connections and their consequences! 4. 6 Connecting the speedometer signal Important : Only an authorised customer service centre should make this connection. The speedometer signal wire connects the system to the vehicle-specific speedometer signal connection. [. . . ] Important : We assume no liability for faulty connections and their consequences! Installation instructions 7 607 621 126 A A F RR R R LF L Fig. 1 * Tel. -Mute (active low) Fig. 4 + + + + - 4 Ohm 4 Ohm 4 Ohm 4 Ohm 7 607 621 129 GPS antenna Bracket A * Fig. 2 1. Fig. 5 A GPS antenna Fig. 3 * 5 2. Radio antenna Installation instructions 6 Fig. 6 ­10 ° ° +30 Fig. 6a 90° 1 2 1 Fig. 7 ­10 ° +30 ° O. K. ­10° 2 90° +3 0° Fig. 8 Installation instructions C-1 1 4 3 2 5 6 C-2 7 10 9 12 8 11 C-3 13 16 19 15 18 14 17 20 A B 1 2 3 4 5 6 7 8 Speaker out RR+ Speaker out RRSpeaker out RF+ Speaker out RFSpeaker out LF+ Speaker out LFSpeaker out LR+ Speaker out LR1 2 3 4 5 6 7 8 9 10 D GND -- -- -- -- -- Sensor -- Sensor -- C B A C 9 10 D 5 6 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Gala/Tacho Tel. -Mute (active low) RFLS Permanent +12V Aut. antenna Illumination Ignition Ground 7 1 3 2 4 8 Wheel sensor C3 13 14 15 16 17 18 19 20 CDC Data-IN CDC Data-OUT +12V Permanent +12V switch voltage (max. [. . . ]