User manual BLAUPUNKT TRAVEL PILOT E1 R BEN

[. . . ] 35 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Displaying the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 38 would like to take advantage of full RDS service, switch to "REG OFF". · Press the AF button for approximately 2 seconds until "REG OFF" appears. "REG ON" or "REG OFF" will appear briefly in the display each time the radio is switched on. Station tuning Automatic tuning · / Press / ; the car radio will automatically search for the next station. If you hold / pressed up or down on the rocker switch, seek tuning will speed up in the upwards or downwards direction. Manual tuning: Press << >>; the frequency will change in short intervals in the downwards or upwards direction. If you hold << >> pressed to the left or the right on the rocker switch, the frequency scan will speed up. · Selecting a waveband With this car radio you can select between the following wavebands: FM 87. 5 - 108 MHz MW 531 - 1602 kHz LW 153 - 279 kHz · Select the desired waveband by pressing the BND button. Note: In the DSC menu it is possible to block MW or LW or both wavebands for station selection. The advantage of doing this is that only the required wavebands can be selected and it is no longer necessary to press BND so often. If necessary, refer to the section on "DSC programming ­ AM ON or AM OFF". Scrolling through the broadcasting networks (FM only) You can use the << >> buttons to tune into stations in your reception area. Seek tuning Up Down << / >> Up/down in short intervals (for FM only, "AF" must be switched off) If it is possible to receive several programmes in the same broadcasting network, you can scroll through them in the forwards direction by pressing >>, or backwards using the << button, e. g. For this to work properly you must have already tuned into the stations at least once and "AF" must be active (lights up in the display). To do this, you can start the Travelstore seek operation: · Press BND for 2 seconds; the system will start to run through the frequency band. You can also tune into a station manually. The scanned frequency or the station name will start flashing in the display. During the actual scanning process "AMSCAN" or "FM-SCAN" will appear in the display. To select a scanned station and switch off the Radio-Scan function: · Press SC or the seek tuning rocker switch briefly. If no station is selected, the scan function will switch off automatically after the frequency band has run through completely. The radio will tune into the station selected before the scan started. Selecting the seek tuning sensitivity You can alter the automatic seek tuning sensitivity. If "lo" is displayed, the radio will only pick up strong, local stations (low sensitivity). If "lo" does not light up, the radio will also pick up weaker, more distant stations (high sensitivity). If you would like to alter the sensitivity level please refer to the section on "DSC programming ­ LO-DX"). PTY - Programme Type PTY is an RDS service which an increasing number of more broadcasting stations have begun to offer. This feature allows you to select FM stations according to their programme type. After you have chosen the PTY of your preference, the corresponding stations can be selected either by seek tuning or using the scan function. Switching PTY on/off · Press PTY. [. . . ] Please read the information in the section on "KeyCard theft protection system "Training" a second KeyCard". 51 PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH The car stereo has been equipped with DSC (Direct Software Control) to allow you to customise certain programmable, basic settings to suit your personal needs and preferences and then store them. CLOCKSET To set the clock manually. Press << >> to set the hours/minutes. Move to the next position (flashing) by pressing / . To store the setting selected, press briefly. [. . . ]