User manual BLAUPUNKT TRAVEL PILOT RNS150B

[. . . ] CD·C button, to select radio, cassette, CD changer (if connected) and AUX sources AUDIO button, to adjust the bass, treble, balance and fader settings. Arrow buttons MENU button, to open the basic settings menu, , to display the time Keys 1 - 5 TRAF button (traffic), to switch traffic information standby on/off PTY, to switch the PTY function on/off Volume control , to increase the volume , to decrease the volume Button to switch the unit on/off, to mute the volume 25 TABLE OF CONTENTS Notes and accessories . . . . . . . . . . 27 Road safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Setting the mute level You can set the unit's mute volume level. Setting the power-on volume You can set the unit's default power-on volume. Press the MENU button =. Keep pressing the or button < until "ON VOL" appears in the display. Press the MENU button =. Keep pressing the or button < until "MUTE LVL" appears in the display. Set the power-on volume using the and buttons <. To help you adjust the volume more easily, the volume will be increased / decreased as you make your changes. If you change the setting to "0", the power-on volume will be the same as the volume level that was set before the unit was last switched off. Note: To protect your hearing, the poweron volume is limited to a value of "38". If the volume level was higher when the unit was switched off, the volume will be reset to "38" when the unit is switched on again. When you have finished making your changes, q Set the mute level using the and buttons <. When you have finished making your changes, press the MENU button =. Mute during telephone operation If your car audio system has been equipped with a mobile telephone, it will automatically switch to mute when you use the phone. This will not work unless the mobile phone is connected to the car audio system as described in the installation instructions. Five stations can be stored on each memory level. 32 RADIO MODE 2 or the FMT button 2 to switch between the memory levels and frequency ranges. DEUTSCH PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Briefly press the BAND (TS) button When using this feature, you will only be able to switch to stations that you have received once already. To do so, use the scan or Travelstore function. Tuning into a station There are various ways of tuning into a station. "T-STORE" appears in the display. After the process is completed, the station stored in FMT memory location 1 will be played. Press the SCAN button 4. Scanning is stopped and the station that was tuned into last will remain active. Setting the scantime Press the MENU button =. Keep pressing the or button < until "SCANTIME" appears in the display. Set the required scantime using the and buttons <. When you have finished making your changes, Listening to preset stations Select the memory or the frequency range. Press the preset station button 1 5 > of the station you want to listen to. press the MENU button = twice. Note: q The set scantime also applies to scanning in CD changer mode. Scanning receivable stations (SCAN) You can briefly play all the receivable stations. You can set the scanning time to between 5 and 30 seconds in the menu. Programme type (PTY) Besides transmitting the station name, some FM stations also provide information on the type of programme that they are broadcasting. Your radio can receive and display this information. For example, the programme types can be: 34 RADIO MODE CULTURE TRAVEL JAZZ SPORT NEWS POP ROCK CLASSICS Using the PTY function, you can directly select stations of a particular programme type. PTY-EON If you specify the programme type and start seek tuning, the radio will switch from the current station to a station of the selected programme type. Note: q If no station is found that corresponds to the selected programme type, you will hear a beep and "NO PTY" appears briefly in the display. [. . . ] When you have finished making your changes, press the MENU button = twice. Displaying the time continuously when the unit is off and the ignition is on To display the time when the unit is off and the vehicle ignition is on, press the MENU button =. Keep pressing the or button < until "CLOCK OFF" or "CLOCK ON" appears in the display. Press the or button < to switch between the ON/OFF settings. When you have finished making your changes, press the MENU button = twice. 42 SOUND AND VOLUME DISTRIBUTION SETTINGS DEUTSCH PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Sound and volume distribution settings You can adjust the sound and volume distribution settings separately for each source (radio, cassette, CD changer and AUX). Setting the left/right volume distribution (balance) To adjust the left/right volume distribution (balance), press the AUDIO button ;. "BASS" appears in the display. Adjusting the bass settings To adjust the bass, Keep pressing the Press the button < until "BAL" appears in the display. press the AUDIO button ;. "BASS" appears in the display. Press the or button < to adjust the bass. [. . . ]