User manual BLAUPUNKT TV-FLEX A-TT 01-M

[. . . ] 5 Opening the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CIosing the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Switching the Monitor's Picture . . . . . . . . . . . . . . . . . . . . . [. . . ] Note · Touch [ RESET ] whilst the minute is below "30" rounds it off, and whilst the minute is "30" or more rounds it up. · No display when the "SYNC" is set to "ON''. Ending the TV Area Setting Screen Touch [ RTN ] to return to the setup menu screen. Ending the Clock Adjustment Screen Touch [ RTN ] to return to the setup menu screen. 10 System Setup Function Code Security Screen 2 Hold down the transmit button on the Mask Key again until the full transmit level indicator lights up in the display. "Code APPROVED" will appear in the display, with the Mask Key function turning on. The s y s t em is now wa i t i ng for you r MA S K KEY s i gna l . Pl ease i npu t now . S y s t em now check i ng for code . s i gna l val id COD E SECUR I T Y RTN Mask Key If you have transmitted the Mask Key's signal once to the unit in advance, you will have to transmit it once again if the unit has been removed from the battery. When using the unit for the first time: If this procedure is not carried out the control panel of the unit will re-open even with your vehicle's ignition turned off. 1 Hold down the transmit button on the Mask Key until the half transmit level indicator lights up in the display. "System now checking for valid signal code" will be displayed. COD E SECUR I T Y RTN If you press the RESET button or remove the battery: The first time you turn the unit on again, "The system in now waiting for your MASK KEY signal. Please input now. " will appear in the display, indicating the setting mode has been entered. Repeat steps 1 and 2 above, and transmit the signal. You can start operating the unit again when "Code APPROVED'' appears in the display. Ending the Code Security Screen Touch [ RTN ] to return to the setup menu screen. Transmission part Transmit button S y s t em now check i ng for code . Setting the interval at the "OFF" factory default indicates no News Timeout will be made, meaning that additional news bulletins will continue to be searched for. · This function is only available if the desired station sends PTY-code for news bulletin or belongs to EON-Network sending PTY-code for news bulletin. Note Sometimes stations in the same network broadcast different programmes or use different programmes service names. Auto TP Seek Function [ATPS] When the Tl function is on and poor reception conditions are experienced when listening to a traffic information station another traffic information station with better reception will be searched for automatically. This function is on, when unit is first powered on. Touch [ ON ] or [ OFF ] to switch the function on and off. s ON: Auto TP seek function is turned on. s OFF: Auto TP seek function is turned off. Ending the RDS Setting Screen Touch [ RTN ] to return to the setup menu screen. Alternative Frequency Function [AF] When poor reception is experienced automatically switch to another frequencybroadcasting the same programme in the same RDS network with better reception. The AF indicator is displayed when the AF function is turned on. Turning AF Function On/Off: Touch [ ON ] or [ OFF ] to switch the function on and off. When no other stations with stronger reception are available for the same programme in the RDS network, you may hear the incoming broadcast in bits and snatches. Turn off the AF function in such a case. Restricting RDS Region (Region Restrict Function) [REG] You can choose whether or not to restrict the RDS channels, received with the AF function for a particular network, to a specific region. [. . . ] If the temperature of the monitor unit drops, the screen may appear darker when power is first turned on due to the characteristics of a liquid crystal panel. Wait a while after turning power on for the temperature to rise. When the unit is set to auto dinner, it is not linked to the vehicle's light switch. Make proper connections according to "Connections" (see page 31). No television/ video image appears. The unit is not connected to the parking brake detection switch. [. . . ]