User manual BLAUPUNKT WOODSTOCK DAB 53

[. . . ] DAB-Radio / CD / MP3 / MMC/SD Woodstock DAB 53 Operating instructions http://www. blaupunkt. com Open here 2 1 2 3 4 16 15 5 6 14 7 8 9 13 12 11 10 3 SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH DEUTSCH DANSK PORTUGUÊS ESPAÑOL CONTROLS DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH 1 2 3 4 5 6 7 8 Button, to unlock the removable control panel (release panel) Volume control Button, to switch the unit on/off and operate the volume mute feature DAB·TS button Short press: to select DAB mode (Digital Audio Broadcast). Long press: to start the DAB Travelstore function. BND·TS button Short press: to select radio mode, the FM memory banks, and the MW and LW wavebands. Long press: starts the FM Travelstore function. [. . . ] "SENS HI6" means that the tuner is set to the highest sensitivity setting. "SENS LO1" means it is set to the lowest sensitivity setting. If "SENS LO" is selected, lo lights up in the display. Set the required sensitivity using the and buttons :. Listening to stored stations Select the memory bank or frequency range (waveband). When you have finished making your changes, press the MENU button 8 or OK ;. Press the station button 1 - 5 > of the station you want to listen to. Storing stations Storing stations manually Scanning receivable stations (SCAN) You can briefly play (scan) all the receivable stations. You can set the scanning time (scantime) to between 5 and 30 seconds in the menu. Starting SCAN Press the OK button ; for longer than two seconds. "SCAN" appears briefly in the display followed by a flashing display of the current station name or frequency. Select the required memory bank, i. e. FM1, FM2, FM3, FMT, or one of the MW or LW frequency ranges. Tune into the station you want to listen to. Press one of the station buttons 1 5 > for longer than two seconds to store the station to that button. 62 RADIO MODE DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Stopping SCAN and continuing listening to a station Press the OK button ;. Scanning is stopped and the station that was tuned into last will remain active. Setting the scantime Press the MENU button 8. Keep pressing the or button : until "SCANTIME" appears in the display. Note: In order to be able to use the PTY function in FM radio mode, it is necessary to deactivate the automatic DAB FM switch (setting: OFF): for more information, read the section "DAB FM Switching" in the Chapter "DAB Operation". PTY-EON If you specify the programme type and start seek tuning, the unit will switch from the current station to a station of the selected programme type. Note: If no station is found that corresponds to the selected programme type, you will hear a beep and "NO PTY" appears briefly in the display. The radio will then retune to the station that was received last. If the tuned radio station or another station on the broadcasting network broadcasts the required programme type at a later point in time, the radio automatically switches from the currently tuned station or from CD mode / CD changer mode to the station whose programme type matches the one you selected. Set the required scantime using the and buttons :. When you have finished making your changes, press the MENU button 8 or OK ; twice. Note: The set scantime also applies to scanning in CD, MMC/SD and CD changer mode. Programme type (PTY) Besides transmitting the station name, some FM stations also provide information on the type of programme that they are broadcasting. Your radio can receive and display this information. For example, the programme types can be: CULTURE TRAVEL JAZZ SPORT NEWS POP ROCK CLASSICS Using the PTY function, you can directly select stations of a particular programme type. Switching PTY on/off Press the MENU button 8. Keep pressing the or button : until "PTY ON" or "PTY OFF" appears in the display. Press the or button : to switch PTY ON or OFF. 63 RADIO MODE When PTY is switched on, PTY appears in the display. Optimising radio reception Treble reduction feature during interference (HICUT) The HICUT function improves reception during poor radio reception (only FM). If interference occurs, the treble is automatically reduced thus reducing the interference level. Switching HICUT on/off Press the MENU button 8 or OK ;. Selecting a programme type and starting seek tuning Press the or button :. The current programme type appears in the display. If you want to select another programme type, you can do so by pressing the or button : whilst this display is visible. Keep pressing the or button : until "HICUT" appears in the display. "HICUT 0" means no reduction will be made, "HICUT 3" means a maximum automatic reduction of the treble level and interference level. Press one of the buttons 1 - 5 > to select a programme type that is stored on one of these buttons. The selected programme type is displayed briefly. [. . . ] Before adjusting the equalizer, set the sound and volume distribution settings to zero and deactivate loudness. For further details, refer to the chapter entitled "Sound and volume distribution settings". When you have finished making your changes, press the MENU button 8. Listen to the CD. What impression does the sound give you? Now read the "Sound impression" column in the table entitled "Help adjusting the equalizer". Set the equalizer values as described in the "Measures" column. 85 EQUALIZER Switching the equalizer on/off To switch the equalizer on, keep the DEQ button < pressed until EQ lights up and "EQ ON" briefly appears in the display. Selecting sound presets You can also select sound presets for the following styles of music. CLASSIC POP JAZZ ROCK TECHNO SPEECH The settings for these music styles have already been programmed. To switch the equalizer off, keep the DEQ button < pressed until EQ disappears and "EQ OFF" briefly appears in the display. Adjusting the equalizer Press the DEQ button <. [. . . ]