User manual BLITZ BZE5P

[. . . ] Keep all electronics away from moisture, dust, extreme heat or extreme vibrations. Blitz Audio products are capable of sound pressure levels in excess of 150dB. Continuous exposure to sound pressure levels over 100 dB may cause permanent loss of hearing. [. . . ] The Volume adjusts the total output level. Fader adjusts the output balance between the front and rear amplifiers. This indicator lights up when the unit is properly powered, grounded, and the remote power lead has power to it. When the "DEF" switch is in the on position the equalizer functions are bypassed. Depressing the "DEF" switch again will restore the equalizer's operation. RCA cables are used to connect your car stereo head unit, DVD player, or other source to either the line or aux inputs. Connect the red wire to the car battery or other power source. Connect the orange wire to the power antenna activating wire of the car stereo. Connect the black wire to the car's chassis for the proper ground connection. RCA cables are used to connect the front channel outputs to the front channel amplifier inputs, the rear channel outputs to the rear channel amplifier inputs, and the sub outputs to the subwoofer amplifier inputs. Parametric EQ Controls Sub Band Parametric Range 35 · 50 · 65 · 80 Hz Low Band Parametric Range 150 · 200 · 260 · 320 Hz Mid Band Parametric Range 600 · 800 · 1000 · 1200 Hz 2. 1 · 2. 8 · 3. 5 · 4. 2 KHz High Band Parametric Range 7 · 9. 5 · 12 · 15 KHz Frequency Response 15 Hz ­ 30 kHz (at +/­ 3 dB, 400 mv) Input Level (for 400 mV Output) 400 mV Total Harmonic Distortion (THD) < 0. 025% (at 400 mV Output) Output Impedance 1. 2 k-Ohm Signal-to-Noise Ratio (S/N) 90 dB Separation 60 dB Subwoofer Frequency Variable from 40-400HZ Control Range ± 12dB Current Drain 0. 5 A Maximum Power Supply Voltage DC, 10 ­ 16 V Neg. Ground Dimensions, W x D x H (inch) 7" (W) x 5. 5" (D) x 1" (H) 5. Power Connections (+12V, Remote, Ground) 12-13. Front, Rear & Subwoofer Outputs 5 Mounting and installation Please take the time to install your new Blitz Signal Processor securely, according to this diagram, using the hardware provided. This Half-DIN size unit can also be installed in the dash adjacent to the head unit, provided that there is a slot available. 4x 6 mm machine screw (4) Dashboard 6 Mounting Bracket 4 x 12 mm self-tapping screw (2) 4 mm spring washer (2) Signal Processor enclosure 4 mm plain washer (2) System wiring Connect 12V DC from a constant battery source to a +12V slip-on spade terminal and install a one (1) amp fuse in line. Connect the signal processor's GROUND to a good chassis ground, near where the unit is mounted, or to the case of the head unit. Connect the signal processor's REMOTE TURN-ON lead to the remote turn-on lead out of the head unit, and install a 1/2 amp fuse in line. (A relay should be used if turning on more than one component, such as EQ's, crossovers or amplifiers. ) Connect stereo RCA cables from the head's left and right front outputs to the left and right inputs of the signal processor. Connect stereo RCA cables from the left and right outputs, (and low, mid and high outputs if applicable), of the signal processor to the left and right inputs of your amplifier(s) or additional signal processor(s). [. . . ] To obtain warranty service you must first call our Consumer Return Hotline number at (718) 236-6948 to obtain a Return Authorization number. This R. A. # must appear on the outside of your package and on all paperwork relating to your return. When returning a product to us for warranty service it must be carefully packed and shipped prepaid to: R. A. # Blitz Service Center 1600 63rd Street Brooklyn, NY 11204 You must also include the following items: · A copy of your sales receipt or other proof of purchase · A brief letter indicating the problem you are experiencing · include in your letter your return address, daytime phone number, and R. A. [. . . ]