User manual BLUE SKY I ON

[. . . ] in wall / on wall passive studio monitor I/ON TM Blue Sky International 70 Sea Lane, Farmingdale, New York, 11735 USA · T: +1 516 249 1399 · F +1 516 249 8870 www. abluesky. com USER MANUAL · CONTENTS I/ON TM Important 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Safety Instructions__ __ __ __ __ __ __ __ __ __ __ Page 3 Welcome to Blue Sky __ __ __ __ __ __ __ __ __ __ Page 4 Welcome to I/ON __ __ __ __ __ __ __ __ __ __ __ Page 4 An Important Note About I/ON __ __ __ __ __ __ Page 4 General I/ON Placement Suggestions__ __ __ __ Page 5 In-Wall Mounting Instructions Using Rails __ __ Page 6 In-Wall Mounting Instructions Using Drywall Anchors __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ Page 7 On-Wall Mounting Instructions __ __ __ __ __ __ Page 8 In-Ceiling Mounting Instructions _ __ __ __ __ __ Page 9 System Signal Connections and Settings__ __ __Page 10 Calibration Guide __ __ __ __ __ __ __ __ __ __ __Page 11 Technical Information _ __ __ __ __ __ __ __ __ __Page 12 I/ON Cabinet Dimensions __ __ __ __ __ __ __ __Page 13 Factory Service Instructions _ __ __ __ __ __ __ __Page 15 General Contact Details __ __ __ __ __ __ __ __ __Page 15 Recycling Information _ __ __ __ __ __ __ __ __ __Page 15 Page 2 · User Manual - Contents USER MANUAL · SAFETY INSTRUCTIONS I/ON 9. TM 1 READ INSTRUCTIONS - Read all safety and operating instructions before operating this product. RETAIN INSTRUCTIONS - Retain these safety and operating instructions for future reference. 2. SERVICING - Do not attempt to service this product yourself. Opening or removing covers, including any over bottom or side speaker drivers, may expose you to dangerous voltage or other hazards. Refer all service to qualified service personnel. [. . . ] Route your wires from the amplifier through this hole. Once I/ON is mounted on the brackets there is . 4" of clearance between the back of I/ON and the wall. If you bring the wire out in the middle Figure 7-c 4/27/07 Step 7 Step 8 Step 2 Step 9 Step 3 Step 10 Step 4 Step 11 Step 12 Step 5 Step 13 Step 14 of the wall behind I/ON, you can route the wire behind the speaker to the push terminals on top or bottom concealing the wire. Remove the template from the wall Using a #2 Philips screwdriver screw the drywall anchors into the drywall using the marks you made in step 5 as a guide. Where the holes are located on a stud, do not screw in drywall anchor. You will see that when bracket slides into the other. Select those brackets and mount them on the wall, using the supplied #8 x 1 ¼" sheet metal screws. Mount them so the stop is towards the bottom of the speaker. Mount the matching brackets to the back of I/ON using #10 X . 75" sheet metal screws. The angle side of the bracket mounds towards the bottom of the speaker. Attach the rubber bumpers to the bottom of the speaker. Strip the end of the speaker wire approximately 1/2 inch then attach the plus wire to the red push terminal and the minus wired to the black push terminal. Check to make sure on is plumb in level and adjust the brackets as necessary. Step 6 Page 8 · User Manual · On-Wall Mounting Instructions USER MANUAL · 8 · IN CEILING MOUNTING GUIDE #10 x 2" Pan Head sheet metal or wood screw 6 plcs into 2 x 4 I/ON TM 2 x 10 Ceiling joist added 2 x 4 3" drywall screws minimum 4 thru 2 x 4 into 2 x 10 24" Ceiling joist removed to show detail Center in openning and flush with drywall Figure 6 Note: The only safe way to mount I/ON on the ceiling is to add Step 6 additional 2 X 4 wooden supports between the ceiling joists and to mount I/ON directly to the wooden supports. Do not use drywall anchors or the supplied mounting rails. The procedure described below assumes that the ceiling joists are 2 inches wide and on 16 inch centers. If the spacing of the ceiling joists are greater than 16 inches, the installer will have to build a 2 x 4 box to support I/ON. If the ceiling joists are warped, you may have to cut down the 2 x 4 studs slightly so the studs clear the opening. Step 7 To mount I/ON the ceiling is a two-person job. Run to run a pair of speaker wires from the amplifier or Step 8 receiver to the desired speaker location. The metal push terminals on I/ON are compatible with the wires up to #8 Step 9 AWG. Cut two 24" long 2 x 4 pieces of lumber, slide through the cutout and drive fit them to the joists. Check that when the two by fours are in place, the 2 X 4s clear the cutout opening. [. . . ] Please do not return the manual or any mounting hardware etc. If you don't have the original packing material and/ or box, please let Customer Service know when you call for the RA number. Blue Sky is not responsible for any damage that occurs due to non-factory packaging. Include a legible note stating your name, shipping address (no P boxes), daytime phone number, RA number, and a . O. [. . . ]