User manual BLUESTORK 85MBPS ETHERNET POWERLINE ADAPTOR

[. . . ] 2 1. 2 Packet Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CHAPTER 2 CONNECTING MECHANISM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. 1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Power Plug connected to any 100V ~ 240V AC power socket. Ethernet Powerline Adaptor 6 2. 3 Hardware Connection ­ Computer For those computers you wish to be networked by Ethernet Powerline Adaptor, each of the computer must be properly connected with an Ethernet Powerline Adaptor through an Ethernet (RJ-45) cable. Following are the steps to properly connect the Ethernet Powerline Adaptor to your computer: 1. Connect the provided Ethernet (RJ-45) cable to the Ethernet Powerline Adaptor's Ethernet port. Connect the other end of the Ethernet (RJ-45) cable to you computer's LAN port. Plug the Ethernet Powerline Adaptor into a wall socket next to the computer. Check and confirm that the Power and Ethernet LEDs on the Ethernet Powerline Adaptor are ON. The hardware connection mechanism is shown below: Ethernet Powerline Adaptor 7 2. 4 Hardware Connection ­ Internet This section describe how to connect the Ethernet Powerline Adaptor into your existing ADSL broadband connection via ADSL Ethernet port. Follow the procedures describe below to connect the Ethernet Powerline Adaptor to your ADSL broadband connection: 1. Connect the provided Ethernet (RJ-45) cable to the Ethernet Powerline Adaptor's Ethernet port. Connect the other end of the Ethernet (RJ-45) cable to an available Ethernet port of your ADSL broadband Router. 4. 6. Plug the Ethernet Powerline Adaptor into a wall socket next to the computer. Check and confirm that the Power, Powerline and Ethernet LEDs on the Ethernet Powerline Adaptor are ON. The hardware connection mechanism is shown below: Ethernet Powerline Adaptor 8 Chapter 4 Installing Management Utility Please verify that no other Ethernet Powerline Adaptor or any Encryption Management Utilities are installed before installing the provided software. "x" shows the number of remote Ethernet Powerline Adaptor discovered by this Management Utility. Network Type: Displayed the type of logical network: "Public" or "Private". Ethernet Powerline Adaptor 12 Autoscan: Shows the scanning status (Default is "ON"). Device Name: Shows the default device name. One may redefine or change the name by clicking on the name and editing in place or by clicking the "Rename" button. Password: Shows the current password of the Ethernet Powerline Adaptor. Quality: Shows the quality of the Ethernet Powerline Adaptor connection. Rate (Mbps): Shows the current transmission rate of the selected Ethernet Powerline Adaptor. MAC Address: Shows the Ethernet Powerline Adaptor's MAC address. Rename: Click to change the name of the selected Ethernet Powerline Adaptor. Enter Password: Shows the supplied Ethernet Powerline Adaptor's password (Initially left blank). To set the Ethernet Powerline Adaptor password (Which is required when creating a private network), click and select the device shown in the lower panel and click on the "Enter Password" button. Follow the pop-up dialog box to complete your password setting. Add: Click this button to add a remote Ethernet Powerline Adaptor to your network that is not on the lower panel displayed list. You will advice to locate the passwords for all Ethernet Powerline Adaptor you wish to manage and add them to the local logical network by clicking the "Add" button. Follow the pop-up dialog box to complete your setting. Scan: Click the "Scan" button to perform an immediate search of the Ethernet Powerline Adaptor connected to the computer. The Management Utility will automatically perform the scanning process and update the display every few seconds by default. Ethernet Powerline Adaptor 13 5. 1. 1 Rename This Management Utility allows you to change the name of the listed Ethernet Powerline Adaptor. Click and select the Ethernet Powerline Adaptor you wish to change from the list, then click on the "Rename" tab and editing-in-place to change the name. Ethernet Powerline Adaptor 14 5. 1. 2 Enter Password To set or change your Ethernet Powerline Adaptor's password, click and select the Ethernet Powerline Adaptor you wish to change from the list, then click on the "Enter Password" tab, the following screen display. Enter your Password (Take note to the password format) and click "OK" after setup. Note: The Ethernet Powerline Adaptor device must be present on the power line (plugged in) in order for the password to be confirmed and added to the network. [. . . ] Check the following: 1. Make sure that the Ethernet cable (RJ-45) is properly connected to the Ethernet Powerline Adaptor's Ethernet port. 2. Make sure that the other end of the Ethernet cable (RJ-45) is properly connected to the computer LAN card or to you Cable/xDSL Ethernet port. 3. 5. Make sure your computer LAN card is properly installed and configured. Make sure your Cable/xDSL broadband access is working and configured correctly. [. . . ]