User manual BLUESTORK BS-SP-CONE BROCHURE

[. . . ] This device may not cause harmful interference This device must accept any interference received including interferences that may cause undesired operations. CE Radiation Norm This equipment has been tested and found to comply with the limits of the European Council Directive 99/5/EC on the approximation of the law of the member states relating to EN 300 328 V1. 4. 1 (2003-04), EN 301 489-1 V1. 4. 1 (2002-08) and EN 301 489-17 V1. 2. 1 (2002-08) and EN 60950. FCC & CE Compliance Statement These limits are designed to provide reasonable protection against radio interference in a residential environment. This equipment can generates, uses and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment ON and OFF, the user is encouraged to try to reduce the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connect to Consult a dealer or an experienced technician for assistance CAUTION! The Federal Communication Commission warns the user that changes or modifications to the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 4 Ports 11g Wireless ADSL2/2+ Router ii Contents COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can define the CoS for all unclassified outgoing packets on layer 2 using this field, which will then pick up the user priority bits based on the mapping rules you create. The selections are (in the order of descending priority): CoS1, CoS2, CoS3, CoS4, CoS5, and CoS6. The default value is CoS1 (recommended). Class of Service: The selections are (in the order of descending priority): CoS1, CoS2, CoS3, CoS4, CoS5, and CoS6. User Priority: The selections are 0, 1, 2, 3, 4, 5, 6, 7. 4 Ports 11g Wireless ADSL2/2+ Router 118 4. 4. 17. 3 Egress Layer 3 Configuration The Egress Layer 3 page (Figure below) enables you to map CoS to ToS so that the priority marking of outgoing packets can be carried over to the IP network. Connection: Select the WAN/LAN interface here to configure the QoS for outgoing traffic to the IP network. Default Non-IP: Locally generated packets (such as ARP packets) do not have a CoS marking. You can define the CoS for all unclassified outgoing packets on layer 3 using this field. The selections are (in the order of descending priority): CoS1, CoS2, CoS3, CoS4, CoS5, and CoS6. The default value is CoS1 (recommended). Class of Service: The selections are (in the order of descending priority): CoS1, CoS2, CoS3, CoS4, CoS5, and CoS6. Translated ToS: The Type of Service field takes values from 1 to 255. Select WLAN interface in LAN Group and click Remove. WLAN moves to the Interface box on the left as shown in figure below. You can configure the WLAN interface to a different LAN group. However, the Ethernet interface is default in LAN group 1 and cannot be moved. Note: 4 Ports 11g Wireless ADSL2/2+ Router 126 2. Select WALN in the Interface box and click Add next to LAN group 2. WLAN moves to LAN group 2 as shown in figure below. The Configure link for LAN group 2 has also been generated, which allows additional configurations for the defined LAN group. 3. 4. Click Apply to temporarily save the changes. To complete and save the setting, click Save All after clicking the Apply button. 4 Ports 11g Wireless ADSL2/2+ Router 127 4. 5. 1. 2 LAN Group Configuration The LAN Group Configuration screen allows you to configure settings for each defined LAN group. Figure below illustrates the default LAN group configuration screen for the default LAN group 1. Notice that you can also view the status of advanced services that can be applied to this LAN group. Click the "Configure" button beside each LAN Group and the following screen display. Unmanaged: Unmanaged is a state when the LAN group is not configured and no IP address has been assigned to the bridge. [. . . ] DHCP is used to serve each LAN-side device and IP address. 4 Ports 11g Wireless ADSL2/2+ Router 244 SNAP: SubNetwork Attachment Point. SNMP: Simple Network Management Protocol: Used to govern network management and monitor devices on the network. SNR: Signal-to-Noise Ratio: Measured in decibels, SNR is a calculated ratio of signal strength to background noise. The higher this ratio, the better the signal quality. [. . . ]