User manual BLUETREK SKIN

[. . . ] It complies with Bluetooth® 1. 2 protocol, supporting Headset and Handsfree profile. PAGE 3 / 9 Charging the BLUETREK® Skin Please connect the charger to the headset and to the main. During the charge, the indicator light is red, the indicator light will turn off when the charge is complete. During subsequent charges, the charging should take approximately 3 hours. When you hear a low-tone beep in your headset at regular intervals, and the indicator light flashes in red, your headset needs to be recharged. [. . . ] BLUETREK® Skin, as packaged, is ready to be worn on your right ear. For left ear, simply unsnap the ear clamp from the headset by pulling gently at the case of the ear clamp ring. The ear hook is made of a soft material which can be shaped to fit your ear. Flip the ear clamp over, and snap it back onto the headset by applying gentle pressure on the case of the ear clamp ring. Switching the BLUETREK Skin ON and OFF Switching BLUETREK® Skin ON When your headset is off, press and hold the TALK button for about 2 seconds until the blue indicator light is on. A beep (2 tones) can be heard in the speaker. To check if your headset is ON, press once on the TALK button. If the indicator light flashes blue, it means your headset is ON. Switching BLUETREK Skin OFF When your headset is on, press and hold the TALK button for about 5 seconds until the red indicator light is on after the quick blue flashes. A beep (2 tones) can be heard in the speaker then release the TALK button. ® ® PAGE 5 / 9 Making a call *Mobile phone with voice recognition . Make sure the voice recognition function on your mobile is activated and your voice tags have been recorded with the phone. To enter these, please refer to your phone's manual . When there is no incoming or active call, press once on the TALK button . Wait for the audio signal sent by the mobile phone (generally a short tone). Speak the name of person you wish to call. Make sure both the headset and the mobile phone are ON and in stand-by mode. Dial the number on the phone keypad, after approximately 2 seconds the audio connection will be established. *This function may not be available on some phones, please refer to the trouble shooting frequent asked questions in our website: www. bluetrek. com. to find out more. Answering a call When the headset rings, press once on the TALK button to take the call. Ending a call Press once on the TALK button to end an active call. Adjusting the volume To increase the volume during an active call, press the "VOL+" button on the headset. To decrease the volume during an active call, press the "VOL-" button on the headset. Muting the microphone To mute the microphone during an active call During an active call, press and hold the VOL+ button for approximately 2 seconds. A periodic tone can be heard in the speaker when the microphone is muted. To end the mute function When the microphone is muted, quickly press the VOL+ button on the BLUETREK® Skin. The periodic tone will end. Transferring a call from BLUETREK Skin to the mobile phone During an active call, press the TALK button for about 2 seconds. (This function only works in the Hands-Free Profile. ) In the Headset profile, you can simply turn off your headset. ® Transferring a call from the mobile phone to the BLUETREK Skin During an active call on the mobile phone, press once on the TALK button to transfer the call. ® PAGE 6 / 9 Pre-registered numbers feature This feature allows you to store your 2 favourite numbers in your BLUETREK® Skin headset and to dial these numbers directly from your headset. (Important: This feature is only available in the Hands-free profile). Storing your favourite numbers 1) Ensure your BLUETREK® Skin headset is paired and connected with your phone. [. . . ] Do not expose your headset to extreme temperatures. Do not expose your headset to fire or open flames. Service and Maintenance can only be performed by BLUETREK® dealers. Keep your headset away from dust and dirt. [. . . ]