User manual BOSCH 900 PEL

[. . . ] Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. [. . . ] in wood ­ in aluminium ­ in non-alloy steel Bevel cuts (left/right) , max. Weight according to EPTA-Procedure 01/2003 Protection class W W min-1 mm mm mm mm ° kg 600 330 500­3100 23 70 12 5 45 2. For lower voltage and models for specific countries, these values can vary. Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary. 24 | English 29 Scale for mitre angle 30 Thumbwheel for pre-tension of base plate (PST 900 PEL) 31 Base plate clamping lever (PST 900 PEL) 32 Lead for the parallel guide 33 Locking screw for parallel guide* 34 Parallel guide with circle cutter* 35 Centring tip of the parallel guide* *Accessories shown or described are not part of the standard delivery scope of the product. A complete overview of accessories can be found in our accessories program. 1 Thumbwheel for stroke rate preselection (PST 800 PEL/PST 900 PEL) 2 Lock-on button for On/Off switch 3 On/Off switch 4 Vacuum hose* 5 Vacuum connection 6 Saw blade storage 7 Base plate 8 Adjusting lever for orbital action 9 Switch for sawdust blowing device 10 Nose for dust cover 11 Sliding shoe (PST 900 PEL) 12 Saw blade* 13 Dust cover for vacuuming* 14 Contact protector 15 Laser line On/Off switch (PST 800 PEL/PST 900 PEL) 16 Laser module (PST 800 PEL/PST 900 PEL) 17 Batteries (PST 800 PEL/PST 900 PEL) 18 Battery lid (PST 800 PEL/PST 900 PEL) 19 Latch of battery lid (PST 800 PEL/PST 900 PEL) 20 Laser warning label (PST 800 PEL/PST 900 PEL) 21 Exit opening for laser beam (PST 800 PEL/PST 900 PEL) 22 Laser viewing glasses* 23 Stroke rod 24 SDS clamping lever for saw blade release 25 Guide roller 26 Splinter guard* 27 Screw (PST 700 PE/PST 800 PEL) 28 Base plate holder (PST 700 PE/PST 800 PEL) PST 700 PE: We declare under our sole responsibility that the product described under "Technical Data" is in conformity with the following standards or standardization documents: EN 60745 according to the provisions of the directives 2004/108/EC, 98/37/EC (until 28 Dec 2009), 2006/42/EC (from 29 Dec 2009). PST 800 PEL/PST 900 PEL: We declare under our sole responsibility that the product described under "Technical Data" is in conformity with the following standards or standardization documents: EN 60745, EN 60825-1 according to the provisions of the directives 2004/108/EC, 98/37/EC (until 28 Dec 2009), 2006/42/EC (from 29 Dec 2009). Before any work on the machine itself, pull the mains plug. While inserting the saw blade, pay attention that the back of the saw blade is positioned in the groove of the guide roller 25. Check the tight seating of the saw blade. A loose saw blade can fall out and lead to injuries. Ejecting the Saw Blade (see figure A2) When ejecting the saw blade, hold the machine in such a manner that no persons or animals can be injured by the ejected saw blade. Turn the SDS lever 24 toward the front in the direction of the contact protector 14. Inserting/Replacing the Laser Module Batteries Insert the supplied batteries 17 into the laser module 16 before starting operation for the first time. Pay attention to the correct polarity according to the representation on the battery lid. Always replace all three batteries 17 together. Use only LR44 batteries from the same manufacturer and with the same capacity. Attaching/Removing the Laser Module Insert the laser module 16 with the inside noses engaging into the notches on the casing of the power tool and push it down to the stop. To remove the laser module, push it upward and remove it from the casing. The laser module must be removed from the power tool when used for stationary work or when sawing from below a workpiece. [. . . ] For this, remove the saw blade from the machine and lightly tap out the machine on a level surface. Heavy contamination of the machine can lead to malfunctions. Therefore, do not saw materials that produce a lot of dust from below or overhead. In extreme working conditions, conductive dust can accumulate in the interior of the machine when working with metal. [. . . ]