User manual BOSCH BSG72233GB

[. . . ] The vacuum cleaner is not suitable for use on building sites. => Vacuuming up building rubble could damage the vacuum cleaner. Switch off the vacuum cleaner when it is not in use. At the end of its life, the vacuum cleaner should be disposed of in an appropriate manner. [. . . ] Therefore, please take used vacuum cleaners to your retailer or recycling centre so that they can be recycled. For current disposal methods, please enquire at your appliance dealership or local council. Only connect the appliance to a socket that is protected by at least a 16 amp fuse. If a fuse should blow when you switch on the vacuum cleaner, this may be because other electrical appliances which have a high current draw are connected to the same power circuit. To prevent the fuse from tripping, select the lowest power setting before switching the vacuum cleaner on, and increase the power only once it is running. 5 Your vacuum cleaner 7 6 8 9 5 10 11 4 12 13 14 3 15 16 2* 17 18 1 24 1 Adjustable floor tool with locking collar 2 Hard-floor brush with locking collar* 3 Turbo brush for floor 4 Turbo brush for upholstery 5 Telescopic tube with adjusting sleeve and locking collar 6 Handle 7 Flexible hose 8 Hard furnishings brush 9 Upholstery nozzle 10 Crevice nozzle 11 Dust bag change indicator 12 Accessories compartment 13 Cover *Only for model BSG72233GB 6 23 22 21 20 19 14 Filter foam 15 Filter holder for micro-hygiene filter 16 Electronic slide control 17 Swing handle; also used as an ON/OFF button and carrying handle 18 Power cord 19 ON/OFF button 20 Parking aid 21 Exhaust filter 22 Storage aid (on underside of unit) 23 Motor protection filter 24 MEGAfilt® SuperTEX dust bag Setting up Before using for the first time Push the handle onto the flexible hose until it engages. CLICK! Insert the flexible hose connector into the opening on the vacuum cleaner until it engages. Push the handle into the telescopic tube until it engages. Push the telescopic tube straight into the connecting piece of the floor tool until it engages. 7 Setting up Release the telescopic tube by moving the adjusting sleeve/sliding switch in the direction of the arrow and adjust the tube to the required length. Take the mains plug, pull the mains cable to the required length and insert the plug into a wall socket. To switch your vacuum cleaner on, press the On/Off button in direction of arrow. The button can also be pressed using the swing handle. 8 Vacuuming min max The required suction power can be selected infinitely variably by adjusting the slide control. Lowest suction range: For vacuuming delicate fabrics, e. g. Low suction range: For cleaning carpets and when there is little dirt. Medium suction range: For vacuuming durable floor coverings, hard floors and for heavily soiled surfaces. High suction range: : For vacuuming stubborn dirt and very heavily soiled surfaces. Adjusting the floor tool: Rugs and carpets hard floors => => Vacuuming with accessories (attach to handle or suction pipe as required). Crevice nozzle For cleaning crevices and corners. 9 Vacuuming a) Upholstery nozzle For cleaning upholstered furniture, curtains, etc. a b b) Furniture brush For vacuuming picture frames, books, delicate furniture, etc. Small accessories that you do not need can be stored in the vacuum cleaner lid. Turbo brush for upholstery Connect the turbo brush to the handle. Brush vacuuming Please note !Only brush vacuum using lower suction levels, i. e. no higher than medium power on the vacuum cleaner. Maintenance Switch off the vacuum cleaner and unplug the power cable before carrying out any maintenance work. Remove the turbo brush from the handle. 10 Vacuuming Cut off any wrapped around hair or threads using a pair of scissors. Then vacuum up the threads and hair using the corner nozzle. Turbo brush for floor Fit the turbo brush onto the suction pipe. Vacuuming with the brush !Only vacuum using performance of the vacuum cleaner. The turbo brush has the possibility to change the rotation speed of the brush from a maximum »A« to a complete stop »B« Moving the slider a little from »A« to »B«permits an optimum cleaning effect for the different floor coverings (long or short pile carpets). Closing completely the fan inlet (position »B«)it is possible to use the device as a normal floor nozzle. 11 Vacuuming Only brush the fringes in the direction of the arrow. Maintenance Always switch off the vacuum cleaner and pull out the plug before performing any maintenance work. Remove the turbo brush from the suction / telescopic pipe. Cut off any wrapped around hair or threads using a pair of scissors. Then vacuum up the threads and hair using the corner nozzle. The lower cover can be removed forcleaning the fan and the fan chamber. To remove the cover act to the two little side wings pushing them toward you, lift up with a light rotation. 12 Vacuuming Open chamber Insert the front lips to reassembly the lower cover Push the cover up to click. observe!Pleaseoperate the turbo brush without the lower cover or with the Never lower cover not well locked. 13 Vacuuming * Hard-floor brush For vacuuming hard floor coverings (tiles, parquet flooring, etc. ) Push the telescopic tube into the connecting piece of the hard-floor brush until it engages. * Press on the locking collar and pull out the telescopic tube to disconnect. * Cleaning the hard-floor brush Vacuum from below to clean the brushes. * If they are very dirty, e. g. with hair wrapped around them, remove both brush rollers from the hard-floor tool. To do so, lever the rollers out from the side of the guide using a screwdriver, or similar object. *Only for model BSG72233GB 14 Vacuuming * Cut through threads and hairs wound round the rollers using scissors. [. . . ] No separate electrical connection is needed. 25 Replacement parts and accessories TURBO-UNIVERSAL® brush for floors BBZ102TBB All-in-one brushing and vacuuming of shallow-pile rugs and carpets and all hard floor coverings. Especially suitable for picking up pet hair. The brush roller is driven by the air flow through the vacuum cleaner. No separate electrical connection is needed. Hard floor brush BBZ123HD For vacuuming hard floors (parquet flooring, tiles, terracotta, etc. ) Washing brush BBZ103WD Suitable for use on all hard floors, such as parquet, laminate, stone, wooden floorboards, tiles, etc. [. . . ]