User manual BOSCH DWA09E750

[. . . ] Extractor hood [en] Instructions for installation and use . . . . . . . . . . 2 Ú Table of contents[ ealon]Instrucisfden INSTRUCTION MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A damaged connection cable must be replaced by a qualified technician (electrician). Always replace defective bulbs immediately (leave bulbs to cool down first) to prevent the remaining bulbs from overloading. 3 Using the appliance Risk of burns!from hot appliance when used with cooking appliances. Keep children away and ensure appliance is used properly. Operating modes This appliance can be used in exhaust-air mode or circulatingair mode. If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used. Exhaust air mode The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system. Circulating-air mode The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen. Note: The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms which contain heating appliances. Before conveying the exhaust air into a non-functioning smoke or exhaust gas flue, obtain the consent of the heating engineer responsible. Note: To bind odours in circulating-air mode, you must install an activated carbon filter. The different options of operating the appliance in circulating-air mode can be found in the brochure or ask your dealer. The required accessories are available from specialist outlets, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use. Operation These instructions apply to several appliance models. It is possible that individual features are described which do not apply to your appliance. Note: Switch on the extractor hood when you start cooking and switch it off again several minutes after you have finished cooking. This is the most effective way of removing the kitchen fumes. Control panel variant 1 Switching on fan: variant 1 Press On/Off button. Increase fan setting by pressing button @ or reduce it by pressing button A. Intensive setting You can use the Intensive setting for particularly strong odour and fume generation. Keep pressing button @ until ~ / > is indicated on the display. Then the appliance sets automatically a lower fan setting. You can always switch back manually. 2Q2II 'LVSOD\ IDQ VHWWLQJV /LJKW 2Q2II Switching on fan: variants 2 and 3 Increase or reduce the fan settings by pressing buttons 1, 2 and 3. Intensive setting: variant 3 Press button ~. 5HGXFH IDQ VSHHG Control panel variant 2 , QFUHDVH IDQ VSHHG , QWHQVLYH VHWWLQJ Light The light can be switched on and off independently of the fan. /LJKW 2Q2II Control panel variant 3 )DQ VHWWLQJV /LJKW 2Q2II 4 )DQ VHWWLQJV 3 , QWHQVLYH VHWWLQJ Installing and removing filter ã=Risk of burns, risk of electric shock! from appliance. Always leave appliance to cool down before cleaning or servicing. Pull metal-mesh grease filter downwards. In doing so, place other hand under the metal-mesh grease filter. 2. Take metal-mesh grease filter out of the holder. Removing metal-mesh grease filter 1. This has no effect on the function of the metal-mesh grease filters. Do not clean heavily soiled metal-mesh grease filters together with utensils. [. . . ] ¯ ) & * Attaching and aligning the appliance 1. Initially remove the protective foil from the back Removing safety caps If the safety caps have to be removed, use a flat screwdriver. of the appliance and, following installation, remove foil completely. When attaching the appliance, ensure that it engages firmly 3. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left. [. . . ]