User manual BOSCH DWK06E650B INSTALLATION INSTRUCTIONS

[. . . ] Extractor hood [en] Instructions for installation and use Ú Table of contents alon[e]Istrucifde INSTRUCTION MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Operating modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Exhaust air mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Circulating-air mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the grain direction only. Do not use any stainless steel cleaners for operator controls. Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents. ■ ■ Operating modes This appliance can be used in exhaust-air mode or circulatingair mode. Circulating-air mode The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen. Exhaust air mode The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system. Note: The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms which contain heating appliances. ■ Before conveying the exhaust air into a non-functioning smoke or exhaust gas flue, obtain the consent of the heating engineer responsible. If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used. Note: To bind odours in circulating-air mode, you must install an activated carbon filter. The different options for operating the appliance in circulating-air mode can be found in the brochure. The required accessories are available from specialist outlets, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use. ■ 4 Operation These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. Note: Switch on the extractor hood when you start cooking and switch it off again several minutes after you have finished cooking. This is the most effective way of removing the kitchen fumes. Control panel Switching on fan Press On/Off button. Increase fan setting by pressing button @ or reduce it by pressing button A. Intensive setting You can use the Intensive setting to extract particularly strong odours or heavy vapours. Press the @ button repeatedly until ˜ or › appears in the display. The appliance then switches back automatically a lower fan setting. You can switch back manually at any time. 2Q2II 'LVSOD\ )DQ VHWWLQJV /LJKW 2Q2II Lighting The lighting can be switched on and off independently of the fan. 6ZLWFK IDQ VHWWLQJ GRZQ 6ZLWFK IDQ VHWWLQJ XS , QWHQVLYH VHWWLQJ Installing and removing the filter : Risk of burns, risk of electric shock! from appliance. Always leave appliance to cool down before cleaning or servicing. Pull metal mesh grease filter downwards. While doing this, place the other hand under the metal mesh grease filter. 2. Take the metal mesh grease filter out of the holder. Removing metal mesh grease filter 1. Open the lock and fold down the metal mesh grease filter. Notes ■ While doing this, place the other hand under the metal mesh grease filter. 2. [. . . ] Initially remove the protective foil from the back of the Removing the safety caps If the safety caps must be removed, use a flat screwdriver. appliance and, following installation, remove the foil completely. When attaching the appliance, ensure that it engages firmly 3. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left. [. . . ]