User manual BOSCH PEX 400 AE

[. . . ] Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. [. . . ] Do not touch the damaged cable and pull the mains plug when the cable is damaged while working. Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. 1 Thumbwheel for orbit frequency preselection (PEX 400 AE) 2 On/Off switch 3 Lock-on button for On/Off switch 4 Dust box, complete (micro filtersystem) 5 Screw for fastening the sanding plate 6 Sanding sheet* 7 Sanding plate 8 Auxiliary handle 9 Wing bolt for adjustment of auxiliary handle 10 Allen key 11 Holder for dust box 12 Plastic slider 13 Extraction outlet 14 Latching lever for dust box 15 Filter element (micro filtersystem) 16 Extraction adapter* The machine is intended for dry sanding of wood, plastic, metal, filler as well as coated surfaces. Machines with electronic control are also suitable for polishing. Random Orbital Sander Article number Preselection of orbital stroke rate Rated power input Output power No-load speed Orbital stroke rate Orbit diameter Sanding plate diameter Weight according to EPTA-Procedure 01/2003 Protection class W W rpm opm mm mm kg PEX 400 A 0 603 310 1. For lower voltage and models for specific countries, these values can vary. Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary. 18 | English ning but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns. Typically the A-weighted noise levels of the product are: Sound pressure level 84 dB(A); Sound power level 95 dB(A). The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. the declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is run- We declare under our sole responsibility that the product described under "Technical Data" is in conformity with the following standards or standardization documents: EN 60745 according to the provisions of the directives 2004/108/EC, 98/37/EC (until Dec. Before any work on the machine itself, pull the mains plug. Depending on the material to be worked and the required rate of material removal, different sanding sheets are available: Material ­ ­ ­ ­ Paint Varnish Filling compound Filler Application For sanding off paint For sanding primer (e. , for removing brush dashes, drops of paint and paint run) For final sanding of primers before coating Grain size coarse medium 40 60 80 100 120 180 240 320 400 Of rough, unplaned beams and boards For face sanding and planing small irregularities For finish and fine sanding of wood Automotive paint Masonry, stone Marble Granite Glass Plexiglas Glass-fibre plastics To remove the sanding sheet 6, lift it from the side and pull it off of the sanding plate 7. [. . . ] A worn sanding plate brake must be replaced by an authorised after-sales service agent for Bosch power tools. Wait until the machine has come to a standstill before placing it down. Sanding Surfaces Switch the machine on, place it with the complete sanding surface on the surface to be worked and move the machine with moderate pressure over the workpiece. the removal capacity and the sanding pattern are mainly determined by the selection of the sanding sheet , the preselected orbital stroke rate (PEX 400 AE) and the applied pressure. [. . . ]