User manual BOSCH PEX 400 OAE & PEX 400 AE,MV

[. . . ] Book Page 15 Friday, September 28, 2007 10:52 AM English | 15 General Power Tool Safety Warnings en WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. [. . . ] The trade names of the individual machines may vary. Book Page 18 Friday, September 28, 2007 10:52 AM 18 | English ning but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns. noise/Vibration Information Measured values determined according to EN 60745. Typically the A-weighted noise levels of the product are: Sound pressure level 84 dB(A); Sound power level 95 dB(A). The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is run- Declaration of Conformity We declare under our sole responsibility that the product described under “Technical Data” is in conformity with the following standards or standardization documents: EN 60745 according to the provisions of the directives 2004/108/EC, 98/37/EC (until Dec. 2007, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen Assembly Before any work on the machine itself, pull the mains plug. Selecting the Sanding Sheet Depending on the material to be worked and the required rate of material removal, different sanding sheets are available: Material – – – – Paint Varnish Filling compound Filler Application For sanding off paint For sanding primer (e. , for removing brush dashes, drops of paint and paint run) For final sanding of primers before coating Grain size coarse medium 40 60 80 100 120 180 240 320 400 fine 1 609 929 M11 | (28. Of rough, unplaned beams and boards For face sanding and planing small irregularities For finish and fine sanding of wood Grain size coarse medium 40 60 80 100 120 180 240 320 400 80 100 120 180 240 320 400 600 1200 fine – – – – – – – Automotive paint Masonry, stone Marble Granite Glass Plexiglas Glass-fibre plastics For pre-sanding For shaping and braking edges For final sanding and forming coarse medium fine For polish-sanding and rounding off edges very fine Replacing the Sanding Sheet To remove the sanding sheet 6, lift it from the side and pull it off of the sanding plate 7. When attaching a new sanding sheet, remove any dust or debris from the sanding plate 7, e. The surface of the sanding plate 7 is fitted with Velcro backing for quick and easy fastening of sanding sheets with Velcro adhesion. Press the sanding sheet 6 firmly against the bottom side of the sanding plate 7. To ensure optimum dust extraction, pay attention that the punched holes in the sanding sheet match with the holes in the sanding plate. replacing the Sanding Plate Note: Replace a damaged sanding plate 7 immediately. Pull off the sanding sheet or polishing tool. [. . . ] Exploded views and information on spare parts can also be found under: www. Com Our customer consultants answer your questions concerning best buy, application and adjustment of products and accessories. Au Disposal The machine, accessories and packaging should be sorted for environmental-friendly recycling. Only for EC countries: Do not dispose of power tools into household waste! [. . . ]