User manual BOSCH PST 900 PEL

[. . . ] Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. [. . . ] For lower voltage and models for specific countries, these values can vary. Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary. 3 On/Off switch 4 Vacuum hose* 5 Vacuum connection 6 Saw blade storage 7 Base plate 8 Adjusting lever for orbital action 9 Switch for sawdust blowing device 10 Nose for dust cover 11 Sliding shoe (PST 900 PEL) 12 Saw blade* 13 Dust cover for vacuuming* 14 Contact protector 15 Laser line On/Off switch (PST 800 PEL/PST 900 PEL) 16 Laser module (PST 800 PEL/PST 900 PEL) 17 Batteries (PST 800 PEL/PST 900 PEL) 18 Battery lid (PST 800 PEL/PST 900 PEL) 24 | English 19 Latch of battery lid (PST 800 PEL/PST 900 PEL) 20 Laser warning label (PST 800 PEL/PST 900 PEL) 21 Exit opening for laser beam (PST 800 PEL/PST 900 PEL) 22 Laser viewing glasses* 23 Stroke rod 24 SDS clamping lever for saw blade release 25 Guide roller 26 Splinter guard* 27 Screw (PST 700 PE/PST 800 PEL) 28 Base plate holder (PST 700 PE/PST 800 PEL) 29 Scale for mitre angle 30 Thumbwheel for pre-tension of base plate (PST 900 PEL) 31 Base plate clamping lever (PST 900 PEL) 32 Lead for the parallel guide 33 Locking screw for parallel guide* 34 Parallel guide with circle cutter* 35 Centring tip of the parallel guide* *Accessories shown or described are not part of the standard delivery scope of the product. A complete overview of accessories can be found in our accessories program. Before any work on the machine itself, pull the mains plug. When mounting the saw blade, wear protective gloves. Danger of injury when touching the saw blade. Selecting a Saw Blade An overview of recommended saw blades can be found at the end of these instructions. The saw blade should not be longer than required for the intended cut. Use a thin saw blade for narrow curve cuts. PST 700 PE: We declare under our sole responsibility that the product described under "Technical Data" is in conformity with the following standards or standardization documents: EN 60745 according to the provisions of the directives 2004/108/EC, 98/37/EC (until 28 Dec 2009), 2006/42/EC (from 29 Dec 2009). Dust Cover Mount the dust cover 13 before connecting the machine to the dust extraction. Insert the dust cover from the front in such a manner that the notches of the dust cover engage into the noses 10 on the machine casing. Remove the dust cover for applications without dust extraction as well as when performing mitre cuts. For this, lightly bend the ends of the dust cover apart and pull it off to the front. Inserting/Replacing the Laser Module Batteries Insert the supplied batteries 17 into the laser module 16 before starting operation for the first time. Pay attention to the correct polarity according to the representation on the battery lid. Always replace all three batteries 17 together. Use only LR44 batteries from the same manufacturer and with the same capacity. Attaching/Removing the Laser Module Insert the laser module 16 with the inside noses engaging into the notches on the casing of the power tool and push it down to the stop. To remove the laser module, push it upward and remove it from the casing. [. . . ] The use of a stationary extraction system is recommended in such cases as well as frequently blowing out the ventilation slots and installing a residual current device (RCD). If worn, it must be replaced through an authorised Bosch after-sales service agent. If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for Bosch power tools. In all correspondence and spare parts order, please always include the 10-digit article number given on the type plate of the machine. [. . . ]