User manual BOSCH SMI 63M52EU/44 SUPPLEMENT

[. . . ] This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Sears, Roebuck and Co. , D/817 WA, Hoffman Estates, IL 60179 If you want your water softener professionally installed, talk to your Sears Salesman. He will arrange for a prompt, quality installation by Sears Authorized Installers. SEARS INSTALLATION POLICY All installation labor arranged by Sears shall be performed in a neat, workmanlike manner in accordance with generally accepted trade practic es. [. . . ] They may scratch and dull the surface. COVERS To keep your new Sears water softener looking nice, apply a coat of paste wax and repeat once a year. When dusty, wipe it with a damp cloth to keep it sparkling. NOZZLE AND VENTURI A clean nozzle and venturi (FIG. 10) is a must for the softener to work right. This small unit moves brine from the salt storage tank to the resin tank during regeneration. If it becomes plugged with sand, silt, dirt, etc. , the softener will not work and you will get hard water. To get to the nozzle and venturi, remove the softener top cover. Be sure the softener is in service cycle (no water pressure at nozzle and venturi). Then, holding the housing tightly with 1 hand, turn the cap off. Lift out the screen support and screen, then the nozzle and venturi. Wash and rinse the parts in warm water until clean. Unplug the transformer at the wall outlet. Remove the salt hole cover and the main cover. Carefully remove the large holding clips at the softener inlet and outlet (see Key No. Separate the softener from the adaptors or bypass valve. Remove the brinewell cover and disconnect the brine valve tubing at the nozzle and venturi assembly (see page 23). Lift the brine valve out of the brinewell. Tip the brine valve upside down to drain out water. 7. 11, lay a piece of 2 inch thick board near the floor drain. SLOWLY and CAREFULLY tip it over until the rim rests on the wood block with the inlet and outlet over the drain. Do not allow the softener's weight to rest on the inlet and outlet fittings or they will break. Tip the bottom of the softener up a few inches and hold until all water has drained. [. . . ] NUMBER 1 7137604 Cover (main) 2 7137612 Salt Hole Cover 3 7118333 Wire Harness (switch) 4 7084330 Power Cord (transformer) 5 7144960 Timer Repl. (PWA) 6 7137620 Face Plate (order req'd decal) 7137670 Face Plate Decal, Mod 625. 3484400 7141475 Face Plate Decal, Mod SMI 63M52EU/44 7 7137599 Rim 8 7137727 Brinewell Cover 9 7143964 Wing Nut, 1/4 10 7100819 Brinewell 11 7144619 Salt Storage Tank 12 7143956 Screw, Plastic, 1/4 x 5/8 13 0900431 Hose Clamp FY 14 1103200 Hose Adaptor FY 15 9003500 Grommet FY 16 7123689 Brine Valve Assy. 29) 17 7105047 Replacement Distributor 18 0501744 Resin 19 7092155 Resin Tank (Incl. 18) 20 7096183 O-Ring, 2-3/4 x 3 21 7077870 Top Distributor 22 0900215 O-Ring, 13/16 x 1-1/16 23 7079092 O-Ring, 2-7/8 x 3-1/4 24 7141001 Vapor Barrier 25 7088041 Clamp Section (2 req. ) 26 7088033 Clamp Retainer (2 req. ) 27 7095373 Transformer, 24V-10VA FY x x 7141417 7147811 Installation manual Owners Manual x not illustrated FY Included in parts bags. [. . . ]