User manual BOSCH SMV88TX02E

[. . . ] SM. . . en Instruction manual en Table of contents no i t cur t sen I l aunam 8 Intended use . 17 Switching off rinse aid refill indicator . 23 , - 7 Environmental protection . 11 Switching on the appliance for the first time . [. . . ] Very sensitive: This setting adjusts the programme strength for difficult conditions of use, for example firmly dried on food remnants. This setting is recommended if using biological or eco detergents which contain lower amounts of active agents. The energy and water consumption is adjusted accordingly. Time display The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). You can change the time display in time or hours/minutes so that the remaining running time of the rinsing progamme appears in the display window “Ready at” (for example 15:20 hours) or “Ready in” (for example 3:25). extraDry The final rinse uses a higher temperature which improves the drying result. (Caution if utensils are delicate!) You can switch the extraDry function on or off. Eco forecast When Eco forecast is activated, the average water and energy consumption of the selected programme is briefly displayed on the display window at the top @. Sensor setting The programme sequence is optmised in Auto programmes with the aid of sensors. The sensors adjust the programme strength of Auto programmes depending on the amount and type of soiling. You can adjust the sensitivity of the sensors in 3 stages. Standard: This setting is ideal for a mixed load and heavily soiled utensils, but also saves energy and water. Sensitive: This setting adjusts the programme strength for the effective removal of food remnants, even if the amount of soiling is low. The energy and water consumption is adjusted accordingly. AutoPowerOff (Switching off automatically after the end of the programme) f O rewoP o t uA To save energy, the dishwasher is switched off 1 minute after the programme ends. You can also change this setting. Possible settings are: ■ off: The appliance does not switch off automatically. ■ After one minute: The appliance switches off after 1 minute. ■ After two hours: The appliance switches off after 2 hours. 31 en Operating the appliance emotionLight (interior light) * t hg i Lno i t ome * depending on the features of your dishwasher The interior light 1" is on when the door is open irrespective of whether the ON/OFF switch ( is switched on or off. When the door is closed or ajar, the interior light is off. You can switch the interior light on or off. Note: Note that when the door is open the interior light is automatically switched off after 1 hour. Infolight * t hg i Lo f n i y a l p s i d t no r F * depending on the features of your dishwasher You can switch the front display ): on or off (additional programme information). Front display * * depending on the features of your dishwasher While the programme is running, a light spot shines on the floor under the appliance door. Do not open the appliance door until the light point is no longer visible on the floor. If the appliance door is not completely closed, the light spot flashes *. If the appliance is installed at eye-level, with flush furniture front, the light point is not visible. You can switch the Infolight on or off. Changing start programme You can change the “Start programme” setting. Tone volume The end of the programme is indicated by a buzzer. You can also change this setting. TimeLight (Optical display while the programme is running) * t hg i Lemi t * depending on the features of your dishwasher While programme is running, an optical display (additional programme information) is indicated on the floor under the appliance door. If the base panel is pulled forwards or if the appliance is installed at eye-level with flush furniture front, the display is not visible. [. . . ] The “Hot water” setting allows you to adjust your dishwasher optimally to operation with hot water. It is recommended to have a water temperature (temperature of the incoming water) of at least 40 °C and no more than 60 °C. It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler. 49 en Installation and connection Electrical connection ■ Removal Also observe the sequence of worksteps here. Disconnect the appliance from the power supply. [. . . ]