User manual BOSCH TDA3610GB

[. . . ] Solving Minor Problems Yourself Problem Possible Causes Temperature control (I) on a very low setting Solution Turn the temperature control to the desired position Iron does not Connection problems Check that the plug is work or is not inserted into the mains heating up socket correctly The automatic shut-off Move the iron gently from system (*) has been activated side to side to re-start it There is no water in the tank Fill the water tank The steam regulator (C) is in Set the steam regulator the «0» position to the relevant position Iron is not Scale obstruction of internal Remove the steam steaming components regulator (C) and clean it. If this does not help contact an Authorised Technical Service Centre Temperature control (I) setting Set the temperature is too low control within the steam area (between the "··" and "max") or turn the steam regulator (C) to «0» You have pressed the shot of Wait 5 seconds between steam button (A) repeatedly each press of the jet of without waiting for 5 seconds steam button between each press Water is dripping from Water has been left in the Always empty the tank the holes in tank (F) when the soleplate after ironing and set the the soleplate was cold, with the steam steam regulator to «0» regulator (C) set at «1» or «2» after ironing and when filling the tank Tap or part distilled water has Mix distilled water with not been used (see "Filling the tap water as directed water tank" section) or other in the "Filling the water products such as fragrant tank" section and never water have been added to the add any other products tank to the water tank Deposits come Traces of lime scale are Carry out a cleaning out through coming out of the steam cycle (see Multiple dethe holes in the chamber scaling system section) soleplate No water in the tank. Spray does not work Obstructed mechanism. Contact an Authorised Technical Service Centre. [. . . ] · The appliance must be used and placed on a stable surface. · When placed on its stand, make sure that the surface on which the stand is placed is stable. · The iron must not be left unattended while it is connected to the supply mains. · Unplug the appliance from the mains supply after each use, or if a fault is suspected. · The electrical plug must not be removed from the socket by pulling the cable. · Never immerse the iron in water or any other fluid. · Do not leave the appliance exposed to weather conditions (rain, sun, frost, etc. ) · With the aim of avoiding dangerous situations, any work or repair that the appliance may need, e. g. replacing a faulty mains cable, must only be carried out by qualified personnel from an Authorised Technical Service Centre. Using Your Iron 1. Auto shut off indicator lamp (*) M. Power cable 3. Setting the temperature The temperature control (I) adjusts the temperature of the soleplate (G). Check the temperature instructions shown on the care label of the garment you are ironing and set the temperature control (I) to the corresponding position by lining it up with the pointer (H) on the iron: Fabric K. Ironing with steam The steam regulator (C) is used to adjust the amount of steam produced when ironing. Make sure that there is water in the tank (F). Adjust the temperature setting and then set the steam regulator, by lining it up with the pointer (D), according to the table below. Steam will automatically be produced: Temperature Setting ··· to "max" ·· Steam Regulator Setting 2 1 A. Water tank cover Temperature Setting · ·· ··· D. Spray outlet Synthetics Silk - Wool Cotton - Linen 3. You can get extra steam by pressing and holding the steam regulator (C) for a maximum of 2 seconds. Note: At a temperature setting of "·", the soleplate is not hot enough to produce steam so the steam regulator should be set to the «0» position to avoid water dripping from the soleplate (G). Filling the water tank Set the steam regulator (C) to the «0» position and unplug the iron from the mains!Use only clean water from the tap and do not mix anything with it. The addition of other liquids, such as perfume, will damage the appliance. [. . . ] It is advisable to first iron a small section on the inside of the garment to see if it is suitable. To attach the fabric protector to the iron, place the tip of the iron into the tip of the fabric protector and press the rear of the protector upward until you hear a click. To release the fabric protector, pull down on the clip at the rear and remove from the iron. C. anti-calc cartridge (model dependent) The anti-calc cartridge has been designed to reduce the build-up of scale produced during steam ironing, helping to extend the useful life of your iron. [. . . ]