User manual BOSCH TDA5620GB

[. . . ] Solving Minor Problems Yourself Problem Possible Causes Temperature control (H) set to minimum Connection problems The automatic shut-off system has been activated (*) There is no water in the tank (D) The steam regulator (A) is in the position Temperature control (H) setting is too low. Solution Turn the temperature control to the desired position Check that the plug is inserted into the mains socket correctly Move the iron gently from side to side to re-start it Fill the water tank Set the steam regulator to the relevant position Set the temperature control within the steam area (between the “••” and “max”) or turn the steam regulator (A) to Turn the steam regulator to a lower setting. Wait 5 seconds between each press of the jet of steam button Iron does not work or is not heating up Iron is not steaming ma x. ma x. Steam regulator (A) is set too high in conjunction with a low temperature. You have pressed the shot of steam button (L) repeatedly without Water is dripping waiting for 5 seconds between from the holes in each press the soleplate Water has been left in the tank (D) when the sole­ late was cold, with p the steam regulator (A) set at or Distilled water has not been used (see “Filling the water tank” section) or other products such as fragrant water have been added to the tank Spray does not work. [. . . ] • This appliance is not intended to be used by persons (including children) with reduced physical, sensory or mental capacities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. • Keep the appliance out of children’s reach. • Children should be supervised to ensure that they do not play with the appliance. • Remove the plug from the socket before filling the appliance with water or before pouring out the remaining water after use. • The appliance must never be placed directly under the tap to fill the water tank. • The appliance must be used and placed on a stable surface. • When placed on its stand, make sure that the surface on which the stand is placed is stable. • The iron must not be left unattended while it is connected to the supply mains. • Unplug the appliance from the mains supply after each use, or if a fault is suspected. • The electrical plug must not be removed from the socket by pulling the cable. • Never immerse the iron in water or any other fluid. • Do not leave the appliance exposed to weather conditions (rain, sun, frost, etc. ) • With the aim of avoiding dangerous situations, any work or repair that the appliance may need, e. g. replacing a faulty mains cable, must only be carried out by qualified personnel from an Authorised Technical Service Centre. DO NOT de-scale or clean the water tank with cleaning products or solvents, as these could cause the iron to drip when using the steam function. DO NOT use a “professional steam cleaner” for cleaning the appliance. Using Your Iron 1. Setting the temperature The temperature control (H) adjusts the temperature of the soleplate (E). 1. Check the temperature instructions shown on the care label of the garment you are ironing and set the temperature control (H) to the corresponding position by lining it up with the pointer (G) on the iron: Fabric Synthetics Silk - Wool Cotton - Linen Temperature Setting • •• ••• 4. Ironing with steam The steam regulator (A) is used to adjust the amount of steam produced when ironing. 1. Make sure that there is water in the tank (D). 2. Adjust the temperature setting and then set the steam regulator according to the table below. Steam will automatically be produced: Temperature Setting ••• to “max” •• Note: At a temperature setting of “•”, the soleplate is not hot enough to produce steam so the steam regulator should be set to the position to avoid water dripping from the soleplate (E). Ironing with shot of steam Steam Regulator Setting J. Filling the water tank ma x ma x. unplug the iron from the mains! [. . . ] When ironing, press the spray button (M) and water will spray out of the spray outlet (C) onto the garment. 9. After finishing each ironing session 1. Unplug the iron from the mains socket. 2. Set the steam regulator (A) to the position. 4. Hold the iron with the point facing down and shake it gently until all the water has come out. [. . . ]