User manual BOSCH VENTARO

[. . . ] Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Do not use the vacuum cleaner when the mains cable is damaged. Do not touch the damaged cable and pull the mains plug when the cable is damaged while working. [. . . ] Multi Sander The multi sander is intended for dry sanding and polishing of wood, filler (except for gypsum) as well as coated surfaces. It is especially suitable for profiles, corners or hard to reach locations. 1 Multi sander 2 On/Off switch of the sander 3 Vacuum hose 4 Vacuum cleaner 5 Latch of the vacuum cover 6 Carrying handle 7 On/Off switch of the vacuum cleaner 8 Vacuum hose connection 9 Plug cap for the vacuum hose connection 10 Holder for blower adapter/closing cover 11 Adapter for blower connection 12 Closing cover with blower filter 13 Cable reel 14 Vacuum lid 15 Bypass valve 16 Closing flap for dust bag enclosure 17 Guide for dust bag 18 Dust bag 19 Drilling helper 20 Extraction adapter, Ø 35 mm 21 Extraction/inflation nozzle 22 Vacuum hose connection of the multi sander 23 SDS button for release of the sanding plate 24 Sanding plate 25 Sanding sheet 26 Pad extender* 27 Sanding plate for extender* 28 Narrow pad extender* 29 Narrow rounded pad extender* *Accessories shown or described are not part of the standard delivery scope of the product. A complete overview of accessories can be found in our accessories program. PSM VENTARO 1400 Air-driven multi sander Article number No-load speed No-load orbital stroke rate Sanding sheet surface Orbit diameter Vacuum cleaner Article number Rated power input Dust bag contents Weight according to EPTA-Procedure 01/2003 Protection class W l min Please observe the article number on the type plate of your multi sander or vacuum cleaner. The trade names of individual machines may vary. the values given are valid for nominal voltages [U] of 230/240 V. For lower voltage and models for specific countries, these values can vary. Typically the A-weighted sound pressure level of the product is 80 dB(A). The noise level when working can exceed 80 dB(A). English | 19 The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. the declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns. vacuum cleaner Measured values determined according to EN 60704. Typically the A-weighted sound pressure level of the product is 77 dB(A). Vacuum cleaner We declare under our sole responsibility that the product described under "Technical Data" is in conformity with the following standards or standardization documents: EN 60335 according to the provisions of the directives 2006/95/EC, 2004/108/EC. Open the closing flap 16 and guide the dust bag 18 from the top into the guide 17 as shown in the figure. [. . . ] Switch on the vacuum cleaner and position the drilling helper 19 against the wall in such a manner that the hole of the drilling helper is flush with the hole to be drilled. Due to the vacuum, the drilling helper remains attached to level surfaces without requiring further aides. Using the Extraction/Inflation Nozzle (see figure E) The extraction/inflation nozzle 21 can be used for vacuuming areas that are difficult to access or for inflating suitable objects. Insert the vacuum hose 3 with the extraction adapter 20 mounted into the extraction/inflation nozzle 21. [. . . ]