User manual BOSE ACOUSTIC WAVE MUSIC SYSTEM I 5-CD CHANGER

[. . . ] WARNING: To reduce the risk of fire or electric shock, do not expose the Acoustic Wave® multi-disc changer to rain or moisture. The apparatus shall not be exposed to dripping or splashing, and objects filled with liquids, such as vases, shall not be placed on the apparatus. As with any electronic product, use care not to spill liquids into any part of the multidisc changer. These CAUTION marks are located on the bottom of your CD changer: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electric shock. [. . . ] Note: The Acoustic Wave® multi-disc changer remote can select an auxiliary component that is connected to the changer, but cannot turn the component on or off or change its settings. figure 5 A new remote with combined controls Turn Acoustic Wave® music system on or off Seek/Tune, when tuned to FM or AM Skip/Scan, when set to CD or CD changer Select: PRESET radio station, when tuned to FM or AM CD (1 through 5) when system is set to CD changer Turn on the system and play the appropriate sound source Play/Pause for single CD player (on top of the Acoustic Wave® music system) STOP for CD changer and single CD player Next disc selection for multi-disc changer Note: If the remote stops operating or its range seems reduced, it may be time to replace the battery. However, be aware that a change in room lighting or other conditions, in addition to battery age, can affect the operating range of an infrared remote control. Using Your Acoustic Wave® Multi-Disc Changer Turning your complete system on and off To turn on both the changer and the Acoustic Wave® music system, press the Play/Pause button (Figure 6) on the changer console. figure 6 Play/Pause button on the Acoustic Wave® multi-disc changer console that turns on both the changer and the Acoustic Wave® music system This turns on both units, so the multi-disc changer is ready to play. ⷠTo turn on only the Acoustic Wave® music system to its last played sound source, press the On/Off key on the new remote control or on the console of the Acoustic Wave® music system. To turn off both the Acoustic Wave® multi-disc changer and the Acoustic Wave® music system, press the On/Off key on the remote control. ⷠTo turn off only the changer, press the On/Off key on the changer console. CAUTION: Do not attempt to load more than one CD in any of the slots. Doing so can cause the discs to jam and be damaged. the Acoustic Wave® multi-disc changer holds up to five CDs. When it is on and a CD is installed, the display indicates the number of the CD selected, the track it is playing, and the elapsed time. To insert a CD into the changer, slip one edge of the disc into an empty slot and press on the opposite edge until the disc is all the way in (Figure 7 on page 9). The LEDs on the front of the unit turn color as follows: · Orange light indicates that the slot is loaded with a CD. This light flashes during ejection of the disc. This light flashes while the changer is switching to that disc. Note: To keep track of the order of CDs in the slots, you may find it useful to keep the CD cases stacked in the same order near the multi-disc changer. To hear the CD you have just inserted, press the Play/Pause button on the console. to remove a CD from a changer slot , press the button to the right of the LED for that slot. Allow a few seconds for the mechanism to respond. Two display panels, two sets of information When the two units first turn on, displays on both consoles light up (Figure 8a). The Acoustic Wave® multi-disc changer display indicates what is playing on the changer. [. . . ] ⷠMake sure nothing is blocking or preventing the IR signals emitted by the multi-disc changer from reaching the receiver on the front of the Acoustic Wave® music system. Refer to "Seating your Acoustic Wave® music system on the multi-disc changer" on page 5. cD skips · Does the unit get bumped in its current location?If so, move it to a more protected location. [. . . ]