User manual BOSS 606C

[. . . ] Disconnect the wire harness and the antenna. Press the release button on the front panel and remove the control panel (see the steps of "remove the front panel"). Lift the top of the outer trim ring then pull it out to remove it. The two supplied keys release tabs inside the unit's sleeve so you can remove it. [. . . ] Do not attempt to disassemble the front panel. Release Button Front Panel 2. Keep front panel into the case. Protective Case Front Panel INSTALL THE FRONT PANEL To install the front panel, insert the panel into the housing and make sure the panel is properly installed. Otherwise, abnormality occurs on the display or some keys will not function properly. 6 WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR FUSE RED IGNITION SWITCH (ACC+) Constant 12 volts GROUND (B­) YELLOW BLACK FUSE (BLACK) AUX IN CABLE Rch RED Lch WHITE FRONT RCA CABLE (BROWN) Rch RED Lch WHITE (GREY) POWER ANTENNA FRONT Lch SPEAKER BLUE REAR RCA CABLE Rch RED Lch WHITE WHITE WHITE/BLACK GREY GREY/BLACK VIOLET VIOLET/BLACK FRONT Rch SPEAKER REAR Lch SPEAKER GREEN GREEN/BLACK REAR Rch SPEAKER 7 OPERATION LOCATION OF KEYS 20 1 3 12 13 5 19 17 496 10 21 7 8 14 15 16 2 18 11 22 8 OPERATION GENERAL OPERATION · ON/OFF Switch on the unit by pressing any button (except REL button (6) and button (4)). When system is on, press POWER button (1) to turn off the unit. · FACEPLATE RELEASE Press REL button (6) to detach the removable faceplate. · LOUDNESS For the unit with two bands only: Press and hold BND/LOU button (8) for several seconds to show the loudness state. And shortly press it again to turn on/off the subwoofer output. In CD mode or AUX mode, press BND /LOU button (8) shortly to show the loudness state. And shortly press it again to turn on/off the bass output. · SET THE CLOCK Press DSP button (9) shortly to switch display mode according to display priority set mode. Press and hold DSP button (9) for several seconds until the clock is shown on the display and flashes, then press VOL+/- button (20)(21) to change hours or the minutes. · SELECT AUDIO MODE Press SEL/MENU (3) shortly to change audio mode through volume, bass, treble, balance, and fader modes. Press the VOL+/- button (20)(21) to adjust the selected mode. When the currently displayed function has not been adjusted for several seconds, the mode shall return to volume position and display will return to normal radio, CD or AUX display. Volume Bass Treble Balance Fader Press the VOL+/- (20)(21) to select your setting. BEEP ON/OFF Program power on volume level CLOCK ON/OFF while power off 12hours/24hours CLOCK/FREQ priority · MENU SELECTION FUNCTION Hold press SEL/MENU (3) for several seconds and you will enter the menu functions then press the SEL/MENU button to select the different modes. 9 BEEP ON/OFF - When the beep is on. It will beep with every button you press. It will not beep when you push a button. Program power on volume level In this mode, you can set the desired volume level when the unit turns on. CLOCK ON/OFF while power off In this mode, you can select if the clock is to be displayed while power off. NO PRI/CLOCK/FREQ priority - When select No Priority: When the frequency appears on the unit, pressing DSP button (9) will display clock and it will not return to frequency display until DSP button (9) pressed again. When the clock appears on the unit, pressing DSP button (9) will display frequency information. - When select Clock Priority: The clock will appear on the unit all the time. Pressing DSP button (9) while in Clock Priority will temporarily display selected station frequency (in RADIO mode) or track number (in CD mode) and then returns to clock display. [. . . ] The operation keys The built-in microcomputer do not work. The radio station automatic selection does not work. Clean the disc or try to play a new one. Cool off or until the ambient temperature return to normal. [. . . ]