User manual BOSS BV-56TS-BV-68TS

[. . . ] 6 Wiring Connection 7 Operation 8 Location and function of keys. . . . . . . . . . . . . . . 8 Switching onloff the unit . . . . . . . . . . . . . . . . . . . . . 10 Openlclose the monitor and angle adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Remote sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 Liquid crystal display . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Then slide the sleeve off the back of the unit. Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle's mounting area. Then use the supplied hardware (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. Spring Washer Metal StrrMounting Bolt , Nut Hex DIN FRONT-MOUNT (Method A) Installation Opening This unit can be installed in any dashboard having an opening as show below: 5. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the outer trim ring. Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. DIN FRONTIREAR-MOUNT This unit can be properly installed either from "Front" (conventional DIN Frontmount) or "Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. Installing the unit Be sure you test all connections first, and then follow these steps to install the unit. 1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. \ Sleeve 2. Press it again to release the function. OPERATION - - Radio Operation Switching to radio mode Press MODE button (12) on the front panel or MODE button (42) on the remote control to select radio mode, the radio mode appears in the display together with the memory band and frequency. Selecting the frequency band Press BND button (11) on the front panel or BAND button (40) on remote control to select desired band. The reception band will change in the following order: Adjusting the equalization - In equalization mode, use VOLUME + I- buttons (7&8) or VOL 4 / b buttons (47) to switch between the following mode and the corresponding information appears on the LCD (4). r+ FLAT --c POP --c JAZZ -+ CLAS L 2 1 T FM1+ FM2 +FM3 +AM1 +AM2 1 - Directly press EQ button (51) to turn on equalization function and to select desired audio mode as above. Mute Press MUTE button (3) on the front panel or MUTE button (43) on remote control to cut down sound output. Press it again to resume the previous volume mode. Setting the clock Press DlSP button (44) to change the display into clock display. While the current time is appeared on the LCD (4), press it again to return to frequency showing. Holding down DlSP button (44) for several seconds, and the time for hours is blinking on the display (4), then press VOLUME + I buttons (7&8) or V O L 4 / bbuttons (47) to switch between hours and minutes. Press TUNE + I- buttons (13&14) or TUNICH A / Vbuttons (46) to adjust the hours or minutes. Selecting station During radio mode, press TUNE + button (13) or TUNICH A button on remote control to increase frequency or TUNE - button (14) or TUNICH V button on remote control to decrease frequency by one step of channel spacing. The frequency is updated corres~ondincllv dis~lav. - on , , < Automatically memory storing & program scanning - Automatic memory storing Press ASIPS button (48) for several seconds, the radio searches from the current frequency and checks the signal strength until one cycle search is finished. And then 6 strongest stations are stored into the corresponding preset number button. [. . . ] Press MOIST button (16) on the front panel or ---, ----I-, ------Press MENU button (19) or (45), the VOLUME will be selected, then press TUNICH A / V buttons (46) to select the item upward or downward. Then press VOL 4 Ib buttons (47) to adjust the selected item. The corresponding value will show on the display. Respectively press PAU (28), INT (29), RPT (30), RDM (31), CD- (32), CD+ (33) button on the panel to enter the corresponding function referring to the CDC operation described above, the corresponding information (such as TV OPERATION CONTROL & FUNCTION KEYS Switching to Nmode Press MODE button (12) on the front panel or MODE button (42) on remote control to select lV mode and the memory channel will show on the TFT display (5). [. . . ]