User manual BOSS BV-650M

[. . . ] CONTENTS Important Safety Instruction 3 Installation 4 DIN Front-Mount (Method A) . . . . . . . . . . . . . . . . 4 Installing the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Removing the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 DIN Rear-Mount (Method B) . . . . . . . . . . . . . . . . . [. . . ] Then replace the outer trim ring. Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. DIN FRONTIREAR-MOUNT This unit can be properly installed either from "Front" (conventional DIN Frontmount) or "Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. Installing the unit Be sure you test all connections first, and then follow these steps to install the unit. 1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. \ Sleeve 2. Disconnect the wire harness and the antenna. Lift the top of the outer trim ring then pull it out to remove it. 4. The two supplied keys release tabs inside the unit's sleeve so you can remove it. One key is for the right side and the other is for the left side. Insert the keys as far as they will go (with the 6. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables. into the sleeve until it locks into place. To further secure the unit, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut (5mm) and Spring 5 INSTALLATION Removing the unit 1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. WIRING CONNECTION DIN REAR-MOUNT (Method B) 3 1 2. Remove the metal strap attached the back of the unit (if attached). 3. Lift the top of the outer trim ring then pull it out to remove it. I VIDEO YELLOW MAIN UNIT I 4. Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard. M R N A L REMOTE CONTROL To the TV unit SWITCH (ACC+) 1. 4. Factory radio mounting bracket Car radio mounting bracket Screw After aligning the car radio mounting bracket with the factory radio mounting bracket, tighten the screws (5x5mm) at 2 places on each side. When fix factory radio mounting bracket with the screws, use a standard-tipped screwdriver to bend open the tabs of the car radio mounting bracket to make them fit into the holes in the factory radio mounting bracket. FRONTLch SPEAKER 1I WHrrVsLACK GREEN I La I' SYNC IN ; : ;0 BLUE :: ;; POWER ANTENNA FRONT Rch SPEAKER GREYIBLACK VIOLET SPEAKER GREENIBLACK Note: The Brake 1 wire is designed to connect to the ground wire, and the Brake 1 wire is designed to connect to CPU. Be sure that these two wires can't be connected to other wires, especially the ACC+ wire and the B+ wire. OPERATION LOCATION AND FUNCTION OF KEYS OPERATION LOCATION AND FUNCTION OF KEYS Fig. / I 4 (OpenIClose button) MUTE LCD TFT Monitor SEL VOLUME+ VOLUMEReset button 11. B AUDIO INPUT 1 VIDEO INPUT 1 MENU CLRIDSP W/AV VOLUME. VOLUME4 CHANNELA CHANNELI IR 4:3/16:9 Selector 28. [. . . ] Selecting receiving mode In TV mode, press N I A V button (21) or (41) to select among lV/AVl/AV2/ RGB. The corresponding state will show on the TFT display (5). When you connect the RGB terminals on the back of the unit to the corresponding RGB system, then press MODE button on remote control to select RGB mode, the RGB signal will appear on the screen. Note: You can receive the lV/AVl/AV2 mode when you brake the car. [. . . ]