User manual BOSS BV9972

[. . . ] · If there is smoke or any peculiar odor present during use or if there is damage to any of the component enclosures, immediately unplug the power cord and send the monitor to your local dealer or service center as soon as possible . Safety precautions · Do not operate this equipment while driving ­ safe driving should always be your highest priority. · This product should not be installed in a location which allows the monitor screen to be visible to the driver of the vehicle. In some states and countries, the viewing of images on a screen inside a vehicle is illegal, even by people other than the driver. Be sure that the installation and operation of this system is in compliance with local rules and regulations. SHOCK HAZARD! [. . . ] Do not install components in areas which are susceptible to rain, moisture, direct sunlight, extreme heat or cold, excessive dust, dirt or humidity. If installation requires drilling holes or other modifications to the vehicle, consult with your nearest dealer or professional car audio installer. Use only the installation parts and hardware provided with the unit to ensure proper installation. Using other parts can cause malfunction and possible damage to your video monitor. Use only a power source with 12 Volts DC (negative ground). Before final installation, temporarily connect the wiring according to the diagram near the end of this manual, check it to ensure that it has been connected properly, and test the unit to make sure it is working correctly. After the monitor is installed, do not arbitrarily pull it down or strike it. This may loosen the mounting screws and cause it to fall down. Operating precautions Turn the unit off when it is not in use. Avoid dropping any metal objects or inflammable items into the monitor ventilation slots. Do not place objects on or suspend objects from the power cord, as this may damage the cord. BVFL10. 4 · BV10. 4IRF · BV7FLIP · BV7IRF User's Manual- page 4 Features Your new video monitor features the following: · TFT Active Matrix LCD display · Overhead console mounting bracket · On-screen menu system · Audio/video input controls · Dual built-in dome lights · Wireless remote control What is included? When first unpacking your new flipdown monitor, please check first that the package contains all of the items below. If something is missing, contact the store where you purchased the player. If you choose to sit to one side of the monitor, you can expect good reception within 35º to the right or left of the monitor. BVFL10. 4 · BV10. 4IRF · BV7FLIP · BV7IRF User's Manual - page 13 On-screen (OSD) menu system This monitor incorporates an on-screen menu display systems which permits you to setup the monitor for a wide variety of installations and applications. Enter the menu system by pressing the MODE button on the front of the monitor or the remote control. Pressing the MODE button steps you through the five main screens of the menu system. These are, in order: Color, Picture, OSD (On Screen Display) Menu, Miscellaneous and Exit. The basic navigation method for this menu system is to: 1 - enter a menu by pressing the MODE button 2 - use the < and > buttons to scroll to the parameter you wish to change 3 - press the MODE button to confirm the selection 4 - use the < and > buttons to adjust the parameter you wish to change 5 - press the MODE button to enter the selection To leave a menu: 1 - press MODE to move to another menu 2 - press MODE a few times until you arrive at the EXIT screen 3 - wait about 15 seconds, after which time the monitor exits the system automatically. Sub-menus in the OSD system Each of the three main menu areas contain submenus permitting you to adjust many aspects of your monitor's behavoir. In the COLOR menu, you can adjust the following: CONTRAST · BRIGHTNESS · HUE · SATURATION In the OSD menu, you can adjust the following: LANGUAGE (language used in the menus) OSD-H and OSD-V (position of image on monitor screen) OSD-TIMER (length of time OSD system remains present after last activity. ON means 5 seconds, OFF means OSD will stay on until you exit the system. TRANSLUCENT (controls if menu background is opaque or translucent. After selecting this function, use the < and > keys to turn translucency on or off). In the MISCELLANEOUS menu, you can adjust the following: SIGNAL SOURCE (permits you to switch between A/V input sources 1 and 2. After selecting this function, use the < and > keys to choose the input source). [. . . ] RESET (YES means return monitor to factory defaults, NO means keep custom settings you have created). BVFL10. 4 · BV10. 4IRF · BV7FLIP · BV7IRF User's Manual - page 14 Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous page. If problems persist, read the following troubleshooting tips which may help eliminate the problems. CAUSE Power cord is not properly connected. A/V input cables not properly connected. [. . . ]