User manual BOSS CD-3155

[. . . ] P6 . P2 . ************** ******* ******* ******* 3. Do not expose the discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a car parked in direct sunlight where there can be a considerable rise in temperature inside the car (P . 3). Do not use your CDs with labels or stickers attached. Labels are attached (P . 7). ******* ******* ******* ******* ******* P7 . Do Not Use Special Shape CDs Be sure to use round shape CDs only for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction. (P . 8). P3 . [. . . ] After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. When the release button is pressed and the D. C. P is unlocked, the car's vibrations may cause it to fall. To prevent damage to the D. C. P always store it in a protective case after detaching it. , The rear connector that connects the main unit and the D. C. P is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. Socket Note: If the D. C. P is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the D. C. P . E-5 5. WIRING DIAGRAM (20 PIN HARNESS PLUG) FUSE ANTENNA JACK ANTENNA R-CH 20-PIN AUDIO/POWER HARNESS (See Figure 1) WHITE L-CH YELLOW AUX IN RED BLUE SUB WOOFER WHITE RCA-TO-RCA CABLES (not supplied) SUB-WOOFER REAR LINE OUT GREY WHITE RED R-CH RCA-TO-RCA CABLES (not supplied) L-CH FRONT LINE OUT BLACK WHITE RED R-CH L-CH AMP BLUE Power Antenna Connect to power antenna or amplifier, If not used, Tape bare end of wire. BLACK Ground Connect to ground terminal or Clean unpainted metal part of chassis Memory/Battery YELLOW Connect to battery or 12 volt power source that is always live. The radio will not work if this wire is not connected RED Accessory/Ignition Connect to existing radio wire or radio fuse. 20-PIN AUDIO/POWER HARNESS LEFT FRONT WHITE-BLACK LFWHITE LF+ RIGHT FRONT GREY-BLACK RF1 GREY RF+ 2 3 4 5 6 7 8 9 10 LEFT REAR GREEN-BLACK LR GREEN LR+ RIGHT REAR VIOLET-BLACK RRVIOLET RR+ 11 12 13 14 15 16 17 18 19 20 Figure 1 Pin View PIN 1 2 3 4 5 6 7 8 9 10 WIRE COLOR GREY/BLACK GREY VIOLET VIOLET/BLACK GREEN GREEN/BLACK RED BLACK RED FUNCTION/LABEL RIGHT FRONT SPEAKER (-) RIGHT FRONT SPEAKER (+) RIGHT REAR SPEAKER (+) RIGHT REAR SPEAKER (-) LEFT REAR SPEAKER (+) LEFT REAR SPEAKER (-) IGNITION(ACC) REAR PRE-AMP LINE OUT COMMON RIGHT REAR PRE-AMP LINE OUT PIN 11 12 13 14 15 16 17 18 19 20 WIRE COLOR WHITE WHITE/BLACK BLUE YELLOW BLACK WHITE RED BLACK WHITE FUNCTION/LABEL LEFT FRONT SPEAKER (+) LEFT FRONT SPEAKER (-) POWER ANTENNA BATTERY(+) CHASSIS GROUND LEFT FRONT PRE-AMP LINE OUT RIGHT FRONT PRE-AMP LINE OUT FRONT PRE-AMP LINE OUT COMMON LEFT REAR PRE-AMP LINE OUT E-6 6. PANEL OPEN/CLOSE OPERATION After the CD is loaded or unloaded, push the panel at position A and the panel will return to its original position. in correct position E-7 7. BASIC OPERATIONS 1) PANEL RELEASE BUTTON (REL) Press this button to remove the control panel. 12)POWER ON/OFF BUTTON Press this button to turn on or off the power. 6) DISPLAY BUTTON (DISP) Press this button briefly, the LCD will display the clock for about 2 seconds, then return to previous display mode. Clock Adjustment Under clock display mode, press DISP button until the LCD flashes, press Tuning Up Button to adjust hour and Tuning Down Button to adjust minute. 3) VARIABLE COLOR DISPLAY BUTTON (COLOR) This unit is equipped with variable color display: The display color can keep changing automatically. Press this button briefly, the display will stop at the color it shows. Press this button shortly again, it will switch to changing color on display. 16) SOURCE BUTTON (SOURCE) Press this button to select Radio and CDP modes. The available selections depends on version: Radio CD Player Radio > CDP > AUX in Sub-woofer On/Off Press SOURCE button for more than 3 seconds to activate or turn off the Sub-woofer output. Aux Input Connect the external signal to the auxiliary line in jack located at the rear of the unit , then press Source button to select Aux mode. Press Source Button again to cancel Aux Mode and return to previous mode. RESET BUTTON The RESET button is located on the main unit (as shown on the diagram). To press it vertically with a ballpoint pen or metal object will activate it. The reset button is to be activated for the following reasons: RE SE T Initial installation of the unit when all wiring is completed. All the function buttons do not operate. Note: If the unit cannot function normally after reseting, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel. E-8 8. AUDIO OPERATIONS 10) ENCODER VOLUME BUTTON To increase the volume, rotate the volume control clockwise to decrease the volume, rotate the volume control counter clockwise. [. . . ] Disc cannot be loaded or ejected Presence of CD disc inside the player. Inserting the disc in reverse direction. Compact disc is extremely dirty or defective disc. The operation keys do not work The built-in microcomputer is not operating properly due to noise. [. . . ]