User manual BOSS FC-50 MIDI FOOT CONTROLLER

[. . . ] To turn on/off the unit Press any button except the EJECT and REL button to turn on the unit. It also can turn on the unit to insert disc or USB. Press the power button and hold for more than 0. 5 seconds to turn off the unit. To select playback mode Press MODE button to select a different mode of operation as indicated on the display panel. [. . . ] STEREO/MONO BUTTON In FM mode, press the MO/ST button to select the STEREO or MONO sound mode. CARE FOR USING CD'S: About CD-R/CD-R/W discs: In addition to commercially-recorded audio CD's, this unit can play CD-R and CD-R/W discs. In come cases, particularly when recorded on older CD burners, some CD-R and CD-R/W discs may not play. Also, whenever you are recording a CD for playback in this receiver, it is recommended that you record at 24x or slower speed for CD-R and 4x or slower for CD-R/W to achieve higher signal quality and better playback performance. To keep the disc clean: Do not attach any sticker or adhesive tape on the disc. Handle the disc by its edge to keep the disc clean and do not touch the surface. Before playing a disc, wipe it off with a clean, dust-free cleaning cloth. Wipe the disc outwards from the disc center. 2. Inset a disc with labeled surface up, or it will damage the unit. Do not expose the disc to direct sunlight or nearby heat sources such as heating vents, caliduct which can cause the disc to warp. Do not leave disc in a car if it is parked in direct sunlight as that will lead to a considerable rise in the temperature inside the car. Do not use any secondhand or rented disc, usually, there is glue on the surface of those discs, it will stop the unit working and damage it. 5. Always store the disc in its case for protection. Scratched up discs will produce poor sound performance and cause CD player to skip. A) Under TRACK SEARCH mode, the LCD will display TRK T 000 and flash the biggest digit 0 that the USB storage or MP3/WMA disc contain. Then rotate the VOL knob on the front panel or hold the + or - button on the remote controller to select the number of the flashing digit from 0 ~ 9. Then press SEL button to confirm the number and flash next smaller digit 0. With the same means, select the number of the flashing digit. After finishing selecting the number of all flashing digit, press SEL button to play the track of the selected serial number. B) Under DIRECTORY SEARCH mode , the LCD will display the root folder(if there is not the root folder, it will find a root folder named ROOT). Then rotate VOL knob or press the + or - button to select your desired folder and then press the >>|/|<< button to select your desired track in the folder. Finally press the SEL button to play the selected track. WIRING CONNECTION BLUE TOOTH ANT ANTENNA PLUG AUX LINE IN (BROWN) 10A FUSE FILTER BOX 0. 5A FUSE RED R WHITE L RED R WHITE L RED R WHITE L YELLOW FRONT RIGHT SP REAR CONSTANT 12 VOLTS GROUND YELLOW BLACK RED RCA LINE OUT REAR(GRAY) RCA LINE OUT FRONT(BLACK) WOOFER LINE OUT IGNITION SWITCH 12 VOLTS BLUE AUTO ANT FRONT LEFT SP REAR WHITE WHITE/BLACK GREEN GREEN/BLACK GRAY GRAY/BLACK VIOLET VIOLET/BLACK NOTES: 1. Only speakers with 4 ohms impedance may be used. Ensure that the blue auto antenna cable does not make contact with any ground connection. Front AUX IN and rear AUX IN can not be connected to at the same time. 7 12 PDF created with FinePrint pdfFactory trial version http://www. pdffactory. com BATTERY INFORMATION OF REMOTE CONTROL Replace Battery in Remote Control : 1. Before using the remote control for the first time, pull the insulating sheet out of the remote control as the direction indicated by the arrow. (see fig. 1) 2. Press the movable block hold as the direction indicated by the A arrow (See fig. 2), then pull the battery holder out of the remote control as the direction indicated by the B arrow(see fig. 2). [. . . ] D) To redial the last phone number dialled E) Short press TELEPHONE button twice continually. It will show the last phone number dialled on LCD. F) Short press TELEPHONE, It will dial the number directly. G) To dial with preset phone number: (1) Short press T-M button; (2) Short press any one of the number buttons or rotate VOL knob to check the preset number. [. . . ]