User manual BOSS HS-IR

[. . . ] USER'S MANUAL page CONTENTS General precautions Safety precautions Installation precautions What is included?Headphone controls and features HS-IR features System wiring: HS-IR transmitter Headphone battery replacement Using HP-10 with a monitor with built-in IR audio transmitter Troubleshooting Specifications HS-IR Wireless Infrared Headphone System (Two Headphones and Transmitter) 2 2 2 2 3 4 5 HP-10 Wireless Headphones (for use with BOSS HS-IR and BOSS Monitors with Infrared Audio Transmission) Congratulations on your purchase of a wireless infrared headphone system. [. . . ] Dangerous high voltages may be present which may result in electric shock. Refer any repairs to a qualified service technician. · Do not attempt to repair a damaged, broken or faulty power cord. · If there is smoke or any peculiar odor present during use or if there is damage to any of the component enclosures, immediately unplug the power cord and send the monitor to your local dealer or service center as soon as possible. What is included? The HS-IR wireless infrared audio system includes: · Wireless audio transmitter · (2) wireless headphones The HP10 is an additional set of wireless headphones for use with the HS-IR system or monitors with wireless infrared audio transmission capability. HS-IR · HP10 User's Manual - page 2 HS-IR and HP10 Headphone Controls and Features 1 2 3 4 5 6 1 5 IR SENSORS 4 POWER LED 6 BATTERY COVER See the section of this manual about battery replacement for more details. 2 VOLUME CONTROL KNOB 3 POWER ON/OFF SWITCH This button turns the headphone on and off. In addition, if headphones do not receive any infrared audio signal after a short period of time, they will shut off automatically to conserve battery life. HS-IR · HP10 User's Manual - page 3 HS-IR Transmitter Features HS-IR 2 2 1 1 IR EMITTERS (AUDIO TRANSMITTERS) 2 MOUNTING HOLE HS-IR · HP10 User's Manual - page 4 System wiring: HS-IR Transmitter Using the wires provided, complete the audio, and power connections in your vehicle as shown in the diagram below. Be sure to locate the transmitter in a location and position within direct line-of-sight of the location in the vehicle you plan to have passengers wearing headphones. AUDIO/VIDEO SOURCE (DVD player, video game, etc. ) WHITE RED LEFT AUDIO OUTPUT RIGHT AUDIO OUTPUT RED FUSE 12V Battery BLACK HS-IR to Chassis Ground HS-IR · HP10 User's Manual - page 5 Installing or replacing headphone batteries The wireless headphones use (2) AAA batteries (not included), which are located in one of the earphone housings. To replace the batteries, follow the diagrams below. To conserve battery life, please be sure to turn off the headphones whenever they are not in use, even though they will turn off after a short period of interrupted IR reception. If you expect the headphones to be unused for several days, remove and store the batteries. Lift battery door release latch. Lift and remove battery door. Insert two AAA type batteries (not included). Be sure to note proper polarity when installing the batteries. HS-IR · HP10 User's Manual - page 6 Using the HP10 headphones with a Boss Monitor Several video monitors include a wireless infrared transmitter. [. . . ] Transmission is best within 6 feet/35º angle of IR sensor on the monitor. Move to a better location. If this is not possible, consider a more suitable location for the transmitter. Specifications MODEL Transmission system Carrier frequency Modulation Mode S/N ratio Channel separation Distortion Frequency response Power source, headphones HP10 Wireless Headphones HS-IR Wireless Headphones with IR Audio Transmitter Infrared light 2. 3 MHz (left channel), 2. 8MHz (right channel) FM Stereo greater than 60 dB greater than 40 dB les than 1% 30Hz - 20kHz (2) x AAA batteries Current consumption, headphones 25 mA max (during play) / 15mA (muted) All specifications subject to change without notice. HS-IR · HP10 User's Manual - page 8 [. . . ]