User manual BOSS RDS514CA

[. . . ] A dirty or defective disc may cause sound dropouts while playing. To enjoy optimum sound, handle the disc as follows. To keep the disc clean, do not touch the surface (P . 1). NOTES ON DISCS If you use the discs explained below, the sticky residue can cause the CD to stop spinning and may cause malfunction or ruin your discs. Do not use second-hand or rental CDs that have a sticky residue on the surface (for example, from peeled-off stickers or from ink, or glue leaking from under the stickers). There are paste residue. [. . . ] Press Source Button again to cancel Aux Mode and return to previous mode. RESET BUTTON The RESET button is located on the main unit (as shown on the diagram). To press it vertically with a ballpoint pen or metal object will activate it. The reset button is to be activated for the following reasons: RE SE T Initial installation of the unit when all wiring is completed. All the function buttons do not operate. Note: If the unit cannot function normally after reseting, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel. E-8 8. AUDIO OPERATIONS 10)ENCODER VOLUME BUTTON Turn this knob to adjust desired volume level. 5) AUDIO BUTTON Press this button to select desired audio function. ORDER OF FUNCTION: VOLUME(VOL) -> BASS(BAS) -> TREBLE(TRE) ->BALANCE(BAL) ->FADER(FAD) While the selected function is displayed, turn Volume Knob to adjust the level within 5 seconds, otherwise the unit will return to volume adjustment mode. 2) MUTE BUTTON (MUTE) Press this button to mute the sound. 17) PRESET EQUALIZER BUTTON (EQ) Press this button to toggle the following EQ settings: FLAT->CLASSICS->POP M->ROCK M->DSP OFF At DSP OFF mode, EQ will be controlled by Bass/Treble setting. 13) BAND/LOUDNESS BUTTON (BAND/LOUD) Press the Band/Loudness Button for couple of seconds to switch the loudness on or off. - TA (Traffic Announcement) When an actual traffic bulletin is on air, the TA indicator will also turn on. E - 11 - PTY (Program Type Codes) This code is used to designate the current program material being broadcast. With this feature, you can search the programs that match the selected program type, which is chosen from a specific list of types. - EON (Enhanced Other Networks Information) It is a supplementary service enabling the radio to obtain information not only from the current station but also from the others. - CT (Clock Time) This function permits to update the clock of the receiver the nation from which the station is broadcasting (from PI). It could happen that on the display will be shown the wrong hour; this happens because in Italy the Clock Time function is not working yet. Notes Depending on the country or region, not all of the RDS functions are available in Italy. RDS may not work properly if the signal strength is weak or if the station you are tuned to is not transmitting RDS data. PROGRAMMABLE OPTIONALS To use this function keep press long SEL Button for few seconds, each time you press this button the mode will move and the functions will shown on the display, turn the volume knob to set the desires functions , the function states as following: - TA SEEK, TA ALARM To determine what action will the radio take if the newly tuned station does not receive TP information for 5 seconds. TA SEEK The radio retunes to a different station which contains TP information. TA ALARM The radio does not retune but beeps will come out. PI SOUND, PI MUTE When the vehicle is crossing the area where two stations with same AF but different PI code can be received at the same time, the receiver will become unstable, under this situation two modes can be selected. PI SOUND The different PI sounds will be heard. [. . . ] To select the tracks under the selected directory, by Rotate ENCODER VOLUME KNOB (ROTATE ANTI-CLOCKWISE First ) then press MP3 ENTER BUTTON to confirm when desired track is found. (D) NAVIGATING THROUGH DIRECTORY BY USING M5/M6 BUTTON Press directory up (M6) or directory down (M5) buttons to skip the current directory forward or backward by one position. In a multi-level directories disc, the movement will take place at the current level until the last directory is reached. At this point press directory down (M5) again , it will move to the next level of directory. ID3 TAG Press DISPLAY button repeatedly to Display ID3 TAG information. If the MP3 file is available with ID3 TAG, pressing the display button repeatedly will show information in the following sequence: SONG TITLE > ARTIST> ALBUM TITLE > YEAR> COMMENTS If any of the ID3-TAG information is not available, pressing the DISPLAY button repeatedly will show information in the following sequence: UNKNOWN SONGNAME> UNKNOWN ARTIST> NO ALBUM TITLE > UNKNOWN YEAR > NO COMMENTS If the MP3 file is without ID3 TAG, pressing the DISPLAY button, & "NO ID3 TAG" will be displayed. [. . . ]