User manual BOSTON ACOUSTICS GT22

[. . . ] When both GREEN and RED remain on, the amplifier is in thermal shutdown condition. RED only indicates a fault condition, "SAFE. " 5 Mechanical Functions Recessed RCA Inputs The input jacks are recessed into the body of the amplifier to provide clearance in tight mounting locations. 1 inch 1 inch Control Cover Removal & Reinstallation The cover panel is secured with two (2) captive coin-slotted screws. Coin-slotted screws allow a coin edge to be used as a screwdriver to remove the panel. Multi-position Mounting Feet The mounting feet are designed to slide in both directions to clear installation obstructions on the mounting surface. Before driving the mounting screws through any surface, be sure of what is behind that surface. [. . . ] The ground wire should be as short as possible and connected directly to the chassis of the vehicle. Make sure that the chassis connection point is free of rust, grease, dirt, paint, and other materials that may insulate the ground wire from making proper connection. Tighten the B+ and GND terminals with the supplied 3mm hex wrench to secure the wire into the terminals. If the power wire must be routed through a drilled or existing hole, use a nylon panel grommet to prevent fraying the wire insulation. Failure to do so could lead to an electrical short if the wire insulation is worn through and the power wire is shorted to ground. 1/ " 4 Strip 5/8" (16mm) Remote Input Connection Use the supplied FEMALE quick-connector to connect the REMOTE trigger lead from the head unit to the amplifier. Crimp connector to wire from head unit that controls remote turn-on (refer to head unit owner's manual). Once the quick-connector is crimped into place, carefully push connector onto recessed MALE REMOTE terminal adjacent to the RCA input pair. Only one (1) remote turn-on terminal should be connected. Speaker Output Connection Prepare each wire by stripping approximately 5/8" (16mm) of insulation. The positive (+) speaker wires are installed into the amplifier terminals marked "SPEAKER OUTPUT" / "+". The negative (­) speaker wires are installed into the amplifier terminals marked "SPEAKER OUTPUT" / "-". Tighten the "SPEAKER OUTPUT", "+", and "-" terminals with the supplied 2mm hex wrench to secure the wires into the terminals. If the speaker wires must be routed through a drilled or existing hole, use a nylon panel grommet to prevent fraying the wire insulation. Failure to do so could lead to an electrical short if the wire insulation is worn through and the speaker wires are shorted to ground. 11 Installation--Fuses & Wiring (cont. ) Mono Subwoofer Operation When the amplifier is configured for mono operation, use the speaker output terminals marked for mono use. Subwoofer impedance must not fall below 2 ohms when in MONO mode. 2-ohm minimum Setup Tuning--Full-range Speakers 1) Music The material chosen for head unit/amplifier system setup must be both clear in recording quality and dynamic in amplitude. Many audiophile "test" discs have musical tracks with both of these characteristics and should be used. 2) Input Sensitivity Control Turn control all the way counterclockwise (minimum position). In this position, the amplifier will be less sensitive to the input signal from the head unit. 3) Highpass & Lowpass Crossover Controls Crossovers should be turned "OFF" during this phase of setup. Move the HIGHPASS and LOWPASS switches to the "OFF" position--with these settings, full-range signal is sent to the speaker outputs. Setting the "Q" control is done in conjunction with setting the levels on the input sensitivity and highpass crossover frequency controls. You may find while setting the "Q" that bottoming may be detected in the front speakers; lowering the "Q" input sensitivity or raising the highpass crossover point will eliminate this. Minor adjustments to each setting are required to fine-tune the system. Setting the "Q" is a subtle process. [. . . ] Excluded from this warranty is damage that results from abuse, misuse, accidents, shipping, or repairs or modifications by anyone other than an authorized Boston Acoustics service representative. This warranty is void if the serial number has been removed or defaced. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. If Service Seems Necessary First, contact the dealer from whom you purchased the amplifier. If that is not possible, write to: Boston Acoustics, Inc. , 300 Jubilee Drive, Peabody, MA 01960 U. S. A. , or your authorized Boston Acoustics distributor We will promptly advise you of what action to take. [. . . ]