User manual BRANDT WFE0610K

[. . . ] WASHING MACHINE USER MANUAL THE CONTENTS SECTION 1:BEFORE USING · · · · · · · Safety warnings Recommendations Removal of the transportation screws Adjustment of feet Electrical connection Water supply connection Water drain connection 2 2 2 3 3 3 4 4 5 6 7 7 7 7 8 8 12 12 13 14 14 15 16 17 17 17 17 18 19 23 SECTION 2: INSTALLATION SECTION 3:TECHNICAL SPECIFICATIONS SECTION 4:CONTROL PANEL · · · · · · · · · · · · · · On/Off button Signal light Function buttons Temperature adjustment knob Program knob Before washing Running the machine Water inlet filters Pump filter Detergent drawer Siphon plug The cabinet The drum Remove of your machine from lime SECTION 5:WASHING YOUR LAUNDRY SECTION 6:MAINTENANCE AND CLEANING SECTION 7: PRACTICAL INFORMATION SECTION 8: AVOIDING MINOR FAULTS SECTION 9:INTERNATIONAL WASHING SIGNS 1 SECTION 1:BEFORE USING SAFETY WARNINGS · · · · · · · · · · · · · · · Do not use a multiple socket or extension cord. Do not insert a plug with damaged or broken cord into the socket. If the cord is damaged it should be replaced by the manufacturer or appointed service agent in order to avoid a hazard. Never remove the plug from the socket by pulling from the cord section. [. . . ] · After you unload your clothes leave the door open for drying of the interior of your machine. · Unplug your machine. WARNING! In case that the electricity goes off and is on again after a while on any stage of the washing programs, your machine will continue the program from the point where it was interrupted. This situation has no harm on your machine. SECTION 6: MAINTENANCE AND CLEANING · · Unplug your machine. Close the water tap. WATER INLET FILTERS On the tap part of your machine's water inlet hose and at the ends of water inlet valves, there are filters to prevent entrance of the dirt and foreign materials in the water to the machine. If the machine is unable to receive sufficient water although your water tap is opened, these filters should be cleaned. · · Remove the water inlet hose. Remove the filters found on the water inlet valves by using a pincer and wash thoroughly with a brush. 14 · · Clean the filters of the water inlet hoses located on the tap side by removing manually together with the seal. After you clean the filters, you can fit them the same way as you have removed. PUMP FILTER The pump filter system elongates the life of your pump, which is used to drain the dirty water. Cleaning of your pump filter in every 2-3 months is recommended. To clean your pump filter: · · · · · · · · Remove the kickplate by pushing with your hand upwards from the lower claws and pulling towards yourself. Before opening the filter cover, place a cup in front of the filter cover to prevent flow of the remaining water in the machine. Loosen the filter cover by rotating it counter clockwise and drain the water. Remove the foreign materials from the filter. Check for the rotation of the pump manually. After you have cleaned the pump, fit the filter cover by rotating clockwise. Fit in the kickplate by holding from the claws and push it. Do not forget that if you do not fit in the filter cover properly, it will leak water. 15 WARNING! Danger of being scalded!Since the water inside the pump maybe hot, wait for it to cool. DETERGENT DRAWER Detergents may form a sediment in your detergent drawer or in housing of the detergent drawer in time. To clean the sediment, pull out the detergent drawer from time to time. To pull out the detergentdrawer: · Pull the detergent drawer to the end. (DIAGRAM-1) · Lift the front of the drawer, continue to pull until the drawer is pull out. (DIAGRAM-2) · Wash will an old toothbrush and excessiveamount of water. · Take off the leftover detergent avoid to drop into your machine. · After drying the detergentdrawer put into the housing in the same manner you pull out. [. . . ] (**)See the section concerning installations your machine. 20 FAILURE PROBABLE CAUSE There is a small amount of clothes in the device. Excessive amount of clothes are filled in the machine or the clothes are not placed in a well-balanced manner. Your machine touches a ripid object. METHODS OF ELIMINATION It does not prevent operation of the machine. [. . . ]