User manual BREVILLE BKE200

[. . . ] · Do not place the Avance® 2 Litre Cordfree Kettle near the edge of a bench or table during operation or when in use. Ensure the surface is level, clean and free of water. · Do not place this appliance on or near a gas burner or electric element, or where it could touch a heated oven. · Keep the kettle clear of walls, curtains and other heat or steam sensitive materials. [. . . ] · The installation of a residual current device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance. See your electrician for professional advice. do Not operAte tHe AvANCe® 2 lItre Cordfree kettle oN AN INClINed SurfACe. do Not move tHe kettle WHIle It IS SWItCHed oN. tHIS kettle SHould Be uSed WItH A reSIduAl CurreNt devICe (SAfety SWItCH) to leSSeN tHe rISk of SCAldINg or otHer INJury from Hot WAter tHAt mAy Be eJeCted If tHe HeAtINg elemeNt eruptS. dISregArd tHIS poINt If your Home IS fItted WItH A reSIduAl CurreNt devICe (SAfety SWItCH). 5 4 know your Breville Avance® 2 litre Cordfree kettle operating your Breville Avance® 2 litre Cordfree kettle Before fIrSt uSe 4. The kettle will automatically switch to the OFF position when the water has boiled. Lift the kettle from the power base and pour the water. Take care to hold the kettle level, especially when filled to the maximum (MAX) level. To re-boil it may be necessary to wait for a few seconds to allow the control to reset. If further heating of the kettle is not required, switch off at the power outlet, unplug the power cord and empty the water from the kettle. Replace the kettle onto the power base and close the lid. Thiskettlemustbeusedwiththepowerbase supplied. Usecautionwhenpouringwaterfromyour kettleasboilingwaterandsteamwillscald. Donot pourthewatertooquickly. On / Off switch with safety auto cut off and boil dry protection Safety locking hinged lid Remove and safely discard any packaging material or promotional labels before using your kettle for the first time. It is recommended before the first use to fill the kettle to the maximum level with cold tap water, bring to the boil then discard the water. Your kettle will only operate when positioned on the power base with the ON/OFF switch in the `ON' position. The kettle will automatically switch `OFF' once the water has boiled. Removable scale filter operAtIoN of your kettle . To fill the kettle with water, remove it from the power base and open the lid by pulling back the lid release latch. Ensure the lid is closed and locked securely into place. Position the kettle firmly onto the power base. Plug the power supply cord into a 230/240V power outlet and switch `On'. Press the ON/OFF switch down to the ON position. The power ON light will illuminate. Alwaysfillthekettlewithwaterbetweenthe minimum(MIN)andmaximum(MAX)markson thewaterwindowonthekettle. Toolittlewater willresultinthekettleswitching. Fillingabovethe maximummark(MAX)mayresultinboilingwater splashingfromthekettle. 2 Litre capacity WArNINg: do Not opeN tHe lId durINg ANd After operAtIoN. tHIS mAy reSult IN BoIlINg WAter SplASHINg from tHe kettle. [. . . ] Alternatively, stains may be removed by: . Filling the kettle until 2/3 full with part white vinegar and 2 parts water. Fill the kettle with clean water, bring to the boil and discard the water. Repeat and the kettle will be ready for use. removAl of mINerAl depoSItS Mineral deposits in tap water may cause the kettle interior and water window to discolour over time. [. . . ]