User manual BRITAX ROEMER VISIO

[. . . ] GB User Guide 0-15Kg (0-4 yrs) Visio 1407. 001 - VISIO AX118 User Guide. indd 1 22/6/07 15:22:47 GB Important! Children up to 15kg (approx. 4 years) Warnings & Guarantee WARNING ­ A CHILD'S SAFETY IS YOUR RESPONSIBILITY Read these instructions carefully before use and keep them for future reference. Your childs safety may be affected if you do not follow these instructions. WARNING ­ This vehicle is only intended for children from birth and up to 15kg. WARNING ­ This vehicle is not suitable for running or skating. [. . . ] This product is not intended for commercial use. WARNING ­ Use a harness as soon as your child can sit unaided. WARNING ­ Any load attached to the handle affects the stability of the pushchair. 1407. 001 - VISIO AX118 User Guide. indd 2-3 22/6/07 15:22:47 Introducing your new pushchair Children up to 15kg (approx. 4 years) Infant Carrier 1 Toddler Carrier 01. Calf Support release latches 19 12 13 03. "D" Rings 14 3 4 15 16 17 7 6 5 18 8 9 10 20 21 23 11 22 08. Folding Handle 1407. 001 - VISIO AX118 User Guide. indd 4-5 22/6/07 15:22:49 1. Assembling your pushchair Children up to 15kg (approx. Using the functions of your pushchair Children up to 15kg (approx. 4 years) 1a 1b Fitting and removal of the front swivel wheels Take each of the front swivel wheel assemblies and press them down onto each of the front legs. You will hear a "click" when they are locked into place (dia 1a). If you need to remove a front swivel wheel, press the wheel release lever (dia 1b) located on the underside of the wheel and lift the wheel assembly from the front leg. 5a 5b Extending and retracting the handles To extend each of the pushchair handles, press the button located at the top of each handle inwards (dia 5a), pull the handles towards you to extend (dia 5b). 2a 2b Unfolding the pushchair Holding the pushchair in a vertical position, lift up on the lock release latches (dia 2a). Push down on the foot lock with your foot whilst pulling both handles up firmly, opening the pushchair until the chassis locks into the open position (dia 2b). Ensure the frame locking latch has locked on both sides. 6a 6b Threading the underside chassis cover straps Place the pushchair on it's side to gain better access to the underside cover straps. Thread the loose end of the strap through both D-rings (dia 6a). Thread the strap back over the last D-ring and back through the first D-ring (dia 6b). Pull the strap tight. 3a 3b Fitting the bumper bar Whilst pressing the button on the bottom of the bumper bar, slide one side of the bar into the armrest socket in the position shown (dia 3a), release the button to engage the lock (dia 3b). Repeat this sequence for the other side. 7a 7b Adjusting the backrest Squeeze clips towards each other to release the backrest lock (dia 7a). Move the backrest into the desired position (dia 7b). 4a 4b Attaching the shopping basket Ensure the basket is fitted with the zips at the sides. Thread the front press stud straps through the metal loops attached to the front of the frame, press studs together (dia 4a). Thread the rear press stud straps around the rear legs and above the frame, press studs together (dia 4b). 8a 8b To adjust the calf support Lower the calf support by lifting up the release latches located underneath both sides of the calf support (dia 8a) and push the calf support down. Raise the calf support by lifting it until the release latches lock into place (dia 8b). 1407. 001 - VISIO AX118 User Guide. indd 6-7 22/6/07 15:22:53 2. [. . . ] To fit the adaptor to the child seat squeeze the lever and insert into the space below the handle (dia 13a). Make sure it is fully fitted and release the lever to lock into place. Repeat this process for both adaptors. 13b 13c Fitting the infant carrier First unfold the armrest covers (please see dia 15a). Lower the infant carrier (will be labelled `Type V, A, B, W') onto the armrests in the orientation shown (dia 13b), making sure that the prongs either side drop into both slots on each armrest. [. . . ]