User manual BROTHER HL-1670N NETWORK USER

[. . . ] Multi-Protocol Print Server NC-4100h USER'S GUIDE Please read this manual thoroughly before using the printer. You can print or view this manual from the CD-ROM at any time, please keep the CD-ROM in a convenient place for quick and easy reference at all times. i Trademarks Brother is a registered trademark of Brother Industries, Ltd. HP, HP/UX, JetDirect and JetAdmin are trademarks of Hewllet-Packard Company. DEC, DEC server, VMS, LAT, and ULTRIX are trademarks of Digital Equipment Corporation. [. . . ] Otherwise you can find it in the "Brother Print Server Configuration Utility" diskette. Note that if desired, you may use a WWW browser or TELNET utility - instead of the BRCONFIG utility). 6-11 CHAPTER 6 NOVELL NETWARE PRINTING Configuring the Brother Print Server (Queue Server Mode in Bindery emulation mode) using PCONSOLE and BRCONFIG 1. Login as Supervisor (NetWare 3. xx) or ADMIN (NetWare 4. 1x or later; be sure to specify the /b option for bindery mode). Execute the BRCONFIG from the Windows menu or insert the "Print Server Configuration Utility diskette in drive A: and type the following at the DOS prompt: A:BRCONFIG or A:BRCONFIG PrintServerName Where PrintServerName is the NetWare print service name of the Brother print server (the default name is BRN_xxxxxx_P1 or BRO_xxxxxx_P1, where "xxxxxx" is the last six digits of the Ethernet address (MAC address)). You can find the NetWare print service name and MAC address by printing out the printer configuration page. Refer to the Quick Setup Guide for information on how to print the configuration page on your print server. If you did not specify the print server name in the BRCONFIG command, select the corresponding server name from the list of print servers. When you get the message that the print server is connected, type the default password "access" in response to the "#" prompt (the password will not echo), and then press the ENTER key in response to the Enter Username> prompt. When you get the Local> prompt, type: 6. SET NETWARE SERVER servername ENABLED 7. Where servername is the name of the file server on which the print queue will reside. If there is more than one file server that you wish to print from, repeat this command as many times as necessary. 6-12 CHAPTER 6 NOVELL NETWARE PRINTING 8. Type EXIT to exit the BRCONFIG remote console program and save the changes and start the Novell PCONSOLE utility. Select Print Server Information (NetWare 3. xx) or Print Servers (NetWare 4. 1x; ignore the warning message) from the Available Options menu. You will be shown a list of current print servers. Press the INSERT key to create a new entry, type in the NetWare print server name (BRN_xxxxxx_P1 or BRO_xxxxxx_P1 by default, where "xxxxxx" is the last six digits of the Ethernet address) and press ENTER. Return to the main Available Options menu by pressing ESCAPE. Select the Print Queue Information (NetWare 3. xx) or Print Queues (NetWare 4. 1x) menu option to see list of configured print queues. Press INSERT to create a new queue on the file server, type the new queue name and press ENTER. The name does not have to be related to the name of the print server resources, but should be short and convenient for users to remember. Make sure that the new queue name is highlighted, and then press ENTER to configure the queue. Select Queue Servers (in NetWare 4. 1x, this item is called Print Servers) and press ENTER to specify which network print servers can print jobs from this print queue. [. . . ] If you do not provide the correct file name, then the upgrade will fail. You must also ensure that the firmware file is set so that the print server can read the file. On Unix systems you can use the chmod command to specify file attributes. For example, chmod filename 666 allows the filename to be accessed by anyone. [. . . ]