User manual BROTHER LX-1200

[. . . ] Owner's Manual ® FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Note -The type of the currently installed cartridge can be viewed through the window in the top cover. -Store the film cartridge at below 113°F (45°C). - 25 - Installing/replacing the film roll in the cartridge Cartridges can be recycled by replacing the film roll. Be sure to use Brother-authorized LC film refills only. Refill cartridges using the following instructions: (1) Remove the film cartridge from the machine being careful not to grab the cartridge by the shutter. Note If the film is stuck, turn on the machine and press the Cut button to remove the excess film. (2) Open the film cartridge by sliding the shutter in the direction of the arrows until it locks into place. Open the film cartridge by gently separating the clear top cover from the gray bottom cover. (3) Remove the old film roll from the cartridge. - 26 - (4) Take the new refill roll of film from the sealed package. Holding the yellow colored plastic side holders of the film roll. Place the film into the cartridge as illustrated. The film can only be placed into the cartridge in the correct direction. Note Remove the separator sheet between film rolls before placing the rolls into the cartridge. 9" and 4. 8" refill rolls may have different side holders. Please refer to the directions that are packed with the refill roll. (5) Remove the side holders (yellow color) of the film roll. (6) Close the film cartridge. Making sure that the leading edge of the film sticks out of the film slit. - 27 - (7) Press on the two shutter buttons marked "PUSH" to release the shutter. (8) The top edge of film should be aligned with the cutting line of the cartridge. If any film extends beyond the cutting line, cut away the excess film as illustrated before installing the cartridge into the machine. (9) Install the cartridge into the machine. (10) Return the roller holder to its original position and press the roller holder levers as illustrated. You will hear the roller holder click into place. - 28 - (11) Close the top cover. (12) Turn the POWER dial to Cutter Off, Border or No Border. Press the Feed button until you can see the edge of the film to remove any slack from the film. CAUTION: To prevent the film from drying out, never open the sealed pack until you are ready to install the cartridge. - 29 - Using 9" (A4) or 4. 8" (A6) film cartridges (1) Turn the POWER dial to OFF and open the top cover. (2) Pull the roller holder levers up and lift the roller holder upwards. (3) Remove the film cartridge carefully. Note If the film is stuck, turn on the machine and press the Cut button to remove the excess film. - 30 - (4) Place the cartridge adapter into the machine as illustrated. 9. 0 inch (5) Place the 9. 0 inch or 4. 8 inch cartridge into the machine. When using the 4. 8 inch cartridge, align the cartridge to the right side of the machine. 4. 8 inch (6) Return the roller holder to its original position and press the roller holder levers as illustrated. You will hear the roller holder click into place. - 31 - (7) Close the top cover. (8) Turn the POWER dial to Cutter Off, Border or No Border. Press the Feed button until you can see the edge of the film to remove any slack from the film. - 32 - Regular maintenance and troubleshooting You can keep your machine in optimum condition by cleaning it on a regular basis. Regular maintenance Avoid small debris and objects Be careful not to let anything slip into the machine, especially metal objects such as paper clips and staples. For optimum lamination results, do not place the machine and cartridges in a dusty environment. Cleaning Never use volatile liquids such as thinner or benzene to clean the exterior surface of the machine. [. . . ] Send to Front Click this tool to bring the active object to the top of a stack of overlapping objects. Send to Back Click this tool to send the active object to the bottom of a stack of overlapping objects. Group Use this tool to group several objects together. First select all the pieces you want to group by clicking on them one by one while holding down the shift key, then click on group. [. . . ]