User manual CADDX NX-6

[. . . ] SECURITY SYSTEM NOTES Installing/Service Company _________________________________ For Service Call __________________________________________ Central Station ___________________________________________ Duress Code ____________________ FUNCTION CODES Function Code Controls Function This system is is not partitioned. EMERGENCY ACTIVATION KEYS (check if enabled) Fire Auxiliary Emergency Police PROGRAMMED FUNCTIONS Cancel Alarm Change Partitions Chime Communicator Test Abort Delay (V) Auto Bypass (V) Auto Instant Battery Test Forced Arming (V) Group Bypass (V) Quick Arm (V) Re Exit Siren Test (V) These features should not be enabled on UL listed systems. ENTRY / EXIT DELAY TIMES Exit Delay Time __________ Entry Delay Time _________ Secondary Exit Delay Time ________ Secondary Entry Delay Time _______ ZONE DESCRIPTIONS 01 _________________________ 02 _________________________ 03 _________________________ 04 _________________________ 05 _________________________ 06 _________________________ 07 _________________________ 08 _________________________ 09 _________________________ 10 _________________________ 11 _________________________ 12 _________________________ 13 _________________________ 14 _________________________ 15 _________________________ 16 _________________________ Note to installer: Identify the wireless zones on UL listed systems. THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET. FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY. [. . . ] Enter 1 or 2 digits indicating the zone you wish to bypass. (Example: Press the [1] key for zone 1, press [1] - [2] for zone 12. ) Press the [BYPASS] key again. The corresponding zone light will illuminate indicating the zone has been bypassed. Repeat steps 3 and 4 for any other zone(s) that need to be bypassed. Press the [BYPASS] key again -or- press the [#] key to exit the Bypass Mode. The bypass light will stop flashing upon exiting the Bypass Mode. Step 4 Step 5 Step 6 GROUP BYPASS By pressing the [BYPASS] key, followed by the [0] key, then the [BYPASS] key again, all zones that are designated as group bypass zones will be bypassed. Press the [BYPASS] key again to exit group bypassing. UNBYPASSING To manually unbypass zones, perform the bypassing procedure on a zone that is already bypassed. The corresponding light for that zone will go off when unbypassed. NOTE: All zones will automatically be unbypassed each time the system is disarmed. TURNING THE DOOR CHIME ON AND OFF The door chime is turned on or off by pressing the [CHIME] key while the system is in the disarmed state. If the chime is on the chime light will be illuminated. If the chime is off, the chime light will be off. Each press of the [CHIME] key will toggle the chime feature on/off and produce a momentary ding-dong sound. 9 CHANGING USER CODES Step 1 Step 2 Step 3 Your system must be in the Disarmed state to change user codes. Enter a "Master Arm/Disarm Code". NOTE: For partitioned systems, someone changing the code of another person must have access to all or more partitions than the user being changed. Enter the 2 digit "user number" (always enter 2 digit such as [0] - [3] for user 3, or [5] - [2] for user 52). Enter the new four (4) or six (6) digit "user code". Note for NX1300 Series LED Keypad: The zone lights will illuminate specifying the first digit of the "user code". (Lights 1-8 on = code is blank; lights 1-8 off = "0"; lights 1 and 8 = "9". ) Use the up and down scroll keys to view the next digit or enter a new 4- or 6-digit "user code". While using the up and down scroll keys you can change any digit by entering a new digit. [. . . ] LOSS OF SYSTEM TIME - This light will illuminate when there has been a loss of power and your system clock needs to be reset. Note: This fault is global in nature and will affect all partitions of a multi-partition system. Press the [#] key to exit the Service Light mode. 2 3 4 5 6 7 8 EXIT 15 EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition. For example, the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building. [. . . ]