User manual CADDX RANGER 8600

[. . . ] SECURITY SYSTEM NOTES Installing / Service Company: For Service Call: Security System Configuration Master Code: Auxiliary Code(s) 2 3 4 5 6 7 "Quick Arm" Digit: Exit Delay Time Entry Delay Time Fire Alarm Sound Burglar Alarm Sound Auxiliary Exit Delay Time Auxiliary Entry Delay Time Steady Siren Yelp Siren 9 9 Pulsing Bell Steady Bell 9 9 Zone Coverage Zone 1: Zone 2: Zone 3: Zone 4: Zone 5: Zone 6: Emergency Phone Numbers Fire Dept. : Police Dept. : Monitoring Center: 1 THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET. FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY. THIS BOOKLET SHOULD BE KEPT IN AN ACCESSIBLE LOCATION FOR THE LIFE OF THE SECURITY SYSTEM. [. . . ] At this time, the "INSTANT" light will illuminate and there will be no entry delay when the entry/exit doors are opened. Any time the "INSTANT" light is on and the exit delay has expired, the opening of an entry/exit door will produce an immediate alarm, making this feature ideal when a high level of security is desired, and no authorized entries are anticipated. By pressing the [r] key again, the "INSTANT" light will turn off, and an entry delay will be present on designated entry/exit doors. NOTE: Your installing company may have programmed the "INSTANT" option to occur in conjunction with the "AUTOMATIC BYPASS" feature. In this case, the "INSTANT" light and the bypassed "ZONE" lights will become illuminated at the end of the exit delay. If this occurs, you still have the ability to turn the "INSTANT" feature off, and/or on by pressing the [r] key. TURNING ON THE CHIME FEATURE Your Security Control Center will operate in the "CHIME" mode to allow the monitoring of selected perimeter doors and windows and designated interior areas while the Security System is not armed. While in the "CHIME" mode, the opening of perimeter doors or windows, or a violation of designated interior areas will cause the Keypad Control to sound (beep) for one second. To use this feature, press the first digit of the Master Code. In five seconds the Keypad Control will sound (beep), indicating that this feature has been enabled. To turn this feature off, press the first digit of the Master Code. In five seconds the Keypad Control will sound (beep), indicating that this feature has been turned off. KEYPAD ACTIVATED PANIC/HOLD-UP ALARM If checked, this feature has been selected by your installing company. If so, when the star [r] and pound [#] keys are pressed at the same time for one second, a local audible alarm will sound. If your system is connected to a monitoring center, an emergency report could be transmitted to that center. These keys should only be pressed in an emergency situation requiring immediate response by law enforcement personnel. PLEASE NOTE: Some Panic/Hold-Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center. Check with your installing company to determine how your security system will respond to the Panic/Hold-Up activation. 4 KEYPAD ACTIVATED FIRE ALARM If checked, this feature has been selected by your installing company. If so, you can activate the Fire alarm by pressing the one [ 1] and three [3] keys at the same time for one second. If your system is connected to a monitoring center, an emergency report could be sent to that center. These keys should only be pressed in an emergency situation requiring response by fire department personnel. FIRE ZONE If checked, your system has zones designated as "FIRE" zones. When this option is selected, and approved heat or smoke detectors are attached to these selected zones, a Fire alarm sound can be initiated from the security system. You should familiarize yourself and your family or staff with this sound (see page 1, Fire Alarm sound) and follow an evacuation plan if this "FIRE" alarm sound is heard. (see page 8 for assistance in formulating an evacuation plan). [. . . ] Always call after the test to ask for results and to put your fire detection system back into service. If the Siren/Bell test option has been selected by your installing company, you may activate the siren/bell by pressing the one [1] and the seven [7] keys at the same time for one second. To silence the siren/bell, enter your 4 digit Master or Auxiliary Code. # # # If any of the above tests are not successful or the results unclear, contact your service company at the phone number listed on page 1 of this booklet. 7 EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition. For example, the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building. [. . . ]