User manual CALCULATOR & CALENDAR DOUBLE PRESS UP CALCULATOR & CALENDAR

[. . . ] • Listening to the tape, radio, CD or digital audio player, etc. with the volume set at a high level for a long period of time will exhaust the battery, while the engine is turned off or while the engine is idling. Be careful not to touch the unit not only when using but after using. DO NOT disassemble the unit since there are no user serviceable parts inside. Fuse* To metallic body or chassis (To an accessory terminal) Remote turn-on line Ignition switch Car battery CALCULATOR & CALENDAR car receiver, etc. Caution To prevent short circuits while making connections, keep the battery’s negative terminal disconnected. [. . . ] • Use the speakers with an impedance of 2 Ω to 8 Ω (4 Ω to 8 Ω: when used in Bridge Mode). • Use the speakers which have sufficient capacity to the unit. The proper lead connected to each SPEAKER OUTPUT terminal is as follows. KS-AX3104/KS-AX3102: AWG 18 to AWG 12 (The cross section is about 0. 8 mm2 to 3. 3 mm2). DOUBLE PRESS UP CALCULATOR & CALENDAR: AWG 18 to AWG 8 (The cross section is about 0. 8 mm2 to 8 mm2). SAFETY INSTRUCTIONS “SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment. DO ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connections. DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment. DO be careful with glass panels or doors on equipment. DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch off, withdraw the mains plug and consult your dealer. Å When your receiver is equipped with line output. ı When your receiver is NOT equipped with line output. KS-AX3104 KS-AX3102 DOUBLE PRESS UP CALCULATOR & CALENDAR Å CALCULATOR & CALENDAR car receiver, etc. Line out ı Speaker input connector. Connector lead a White "LEFT (+)" b Black "RECEIVER GND" To Receiver = Left (+) lead = Chassis*1 = Right (+) lead *2 INPUT HIGH INPUT L/MONO LEVEL c Gray "RIGHT (+)" CROSSOVER LPF OFF HPF FRONT REAR MIN MAX R • Connect each lead of the speaker input connector to a speaker positive lead or chassis*1 of the receiver. • Cover the terminals of unused speaker negative leads of the receiver with insulating tape to prevent short circuits. *1 Example: connecting to the ground Rear ground terminal Black lead of the speaker input connector RECEIVER GND 2-speaker system plus subwoofer • Use the speakers with an impedance of 2 Ω to 8 Ω. Line out (Rear) or Subwoofer out Å CALCULATOR & CALENDAR car receiver, etc. *2 CALCULATOR & CALENDAR amplifier, etc. (Purchased separately) CALCULATOR & CALENDAR car receiver, etc. Line out (Front) *2 INPUT FRONT REAR ı Speaker input connector. Connector lead a White "LEFT (+)" b Black "RECEIVER GND" c Gray "RIGHT (+)" CROSSOVER LEVEL LPF OFF HPF *2 Not supplied To Receiver Subwoofer = Left (+) lead = Chassis*1 = Right (+) lead KS-AX3104 4-speaker system—Normal Mode • Use the speakers with an impedance of 2 Ω to 8 Ω. Front Å CALCULATOR & CALENDAR car receiver, etc. Line out (Front) * 2 HIGH INPUT L/MONO Front MIN MAX R * 2 Rear Line out (Rear) HIGH INPUT LEVEL CROSSOVER LPF OFF HPF Subwoofer system—Bridge Mode Rear • Use the speakers with an impedance of 4 Ω to 8 Ω. Å CALCULATOR & CALENDAR car receiver, etc. CROSSOVER LPF OFF HPF HIGH INPUT LEVEL INPUT L/MONO L/MONO ı Speaker input connector. Line out (Rear) or Subwoofer out *2 Connector lead a White "LEFT (+)" b Black "RECEIVER GND" c Gray "RIGHT (+)" CROSSOVER LEVEL LPF OFF HPF MIN MAX MIN MAX To Receiver R R = Left (+) lead = Chassis*1 = Right (+) lead FRONT REAR ı Speaker input connector. Connector lead a White "FRONT LEFT (+)" b Black "RECEIVER GND" c Gray "FRONT RIGHT (+)" To Receiver 1 Connector lead d Green "REAR LEFT (+)" e Black "RECEIVER GND" f Purple "REAR RIGHT (+)" To Receiver INPUT HIGH INPUT L/MONO = Front left (+) lead = Chassis* = Front right (+) lead = Rear left (+) lead = Chassis* 1 MIN MAX = Rear right (+) lead R Subwoofer 2-speaker system plus subwoofer—Bridge Mode • Use the speakers with an impedance of 2 Ω to 8 Ω. [. . . ] • Leave the unit turned off to cool it down if it heats up abnormally. Å CALCULATOR & CALENDAR car receiver, etc. *2 *2 CALCULATOR & CALENDAR amplifier, etc. (Purchased separately) Line out (Center) *2 Subwoofer out Line out (Rear) ı Speaker input connector. *2 PRE OUT L INPUT HIGH INPUT L/MONO Front Speaker Rear Speaker No sound is heard. • Confirm the connections for the power supply (see "POWER SUPPLY" on page 1). • Connect the RCA pin cords to the INPUT jacks, or the speaker input connector to the HIGH INPUT terminal. • Confirm the speaker wirings and the position of the CROSSOVER filter switch (See “SPEAKER CONNECTIONS” on page 2). Connector lead a White "LEFT (+)" b Black "RECEIVER GND" c Gray "RIGHT (+)" To Receiver = Left (+) lead = Chassis*1 = Left (+) lead R R Alternator noise is heard. • Keep the leads of the POWER terminals away from the RCA pin cords. [. . . ]