User manual CALIBRE CALIBREDL INS

[. . . ] Position the Warning Pod(s) on the dash with the provided double stick "O" ring tape. CALIBRE DL-P models require the mounting of a second Pod for rear radar warnings. Route the black cable(s) from the Warning Pod(s) through or under the dash per DIAGRAM B1. FRONT WARNING POD REAR WARNING POD "O" RING TAPE "O" RING TAPE EY R G BL UE W HI TE DIAGRAM B1 EY R G Interior Network Module 1. Remove the under dash panel and mount the Interior Network Module using the supplied cable ties to the existing factory wire looms, brackets, or other support structures as per DIAGRAM C1. [. . . ] Position the Laser Defuser around the existing front license plate and mount it against the factory license plate bracket. Use the existing mounting bolts or K40 supplied nylon bolts to secure the Laser Defuser frame and license plate to the bracket. NOTE: On vehicles that have only one set of bracket mounting holes, it is recommended that the Laser Defuser and the license plate be bolted together to eliminate any vibration. 3. For proper performance, the Laser Defuser must be mounted completely level. Use the K40 supplied nylon nuts and bolts to correct the mounting angle of the Laser Defuser either up or down as needed. Route the black and clear zip cord wires into the engine compartment either through the grill or under the bumper. Connect with radar receiver wires per the separate enclosed block diagram sheet. LASER DEFUSER LASER DEFUSER LASER DEFUSER FACTORY MOUNTING LOCATION FACTORY MOUNTING LOCATION FACTORY MOUNTING LOCATION MOUNTING NUTS CORRECT NO DIAGRAM F1 NO NOTE: On some vehicles, it may be necessary to adjust or reposition the factory license plate bracket to achieve the desired level installation. CUSTOM Mount 1. Separate the Laser Defuser module from the license plate frame by removing the two screws on the backside of the frame. Choose a mounting location near the center of the vehicle that has a clear, unobstructed view of the road. See DIAGRAM G1. CENTERED & UNOBSTRUCTED DO NOT PUT BEHIND GRILL DO NOT OBSTRUCT VIEW DO NOT MOUNT OFF CENTER DIAGRAM G1 3. If utilizing the supplied universal mounting bracket, determine which holes will be used to mount the Laser Defuser to the vehicle. Remove the unused mounting tabs on the bracket as needed. Apply the supplied double stick tape directly to the Laser Defuser and attach the Laser Defuser to the universal mounting bracket with the included 1/4" screws. See DIAGRAM G2. BRACKET BRACKET TAPE TAPE 1/4" SCREW LASER DEFUSER WITHOUT HORIZONTAL TABS 1/4" SCREW LASER DEFUSER WITH HORIZONTAL TABS 1/4" SCREW 1/4" SCREW Diagram G2 5. Install the Laser Defuser to the desired mounting surface using the included 3/4" screws or nylon mounting nuts and bolts. For proper performance, the Laser Defuser must be mounted perfectly level, facing straight ahead, and as far forward on the front of the vehicle as possible. See DIAGRAMS G3 and G4. Enlarged View JAMMING BEAM Enlarged View M EA GB IN MM JA LASER DEFUSER LASER DEFUSER CORRECT JAMMING BEAM DIAGRAM G3 NO AM ING BE JAMM Enlarged View Enlarged View LASER DEFUSER LASER DEFUSER CORRECT DIAGRAM G4 NO 7. Route the black and clear zip cord wires into the engine compartment either through the grill or under the bumper. Connect with radar receiver wires per the separate enclosed block diagram sheet. REAR RADAR RECEIVER NOTE: The rear radar receiver can be mounted behind plastic, rubber, or fiberglass up to 1/4" thick. Do not mount radar receiver behind metal or chromed plastic. 1. The rear radar receiver can be fastened to the vehicle using the supplied self-tapping screws or cable ties. [. . . ] Use the K40 supplied nylon nuts and bolts to correct the mounting angle of the Laser Defuser either up or down as needed. See DIAGRAM I1. NOTE: On some vehicles, it may be necessary to adjust or reposition the factory license plate bracket to achieve the required level mounting. LASER DEFUSER FACTORY MOUNTING LOCATION LASER DEFUSER FACTORY MOUNTING LOCATION LASER DEFUSER FACTORY MOUNTING LOCATION MOUNTING NUTS DIAGRAM I1 4. Route the black and clear zip cord wires into the trunk and connect wires per the separate enclosed block diagram sheet. CUSTOM Mount 1. Remove the mounting bolts and any existing frame or cover from the rear license plate. [. . . ]