User manual CAMBRIDGE AUDIO INCOGNITO LM10 INSTALLATION GUIDE

[. . . ] Check all connections and test the system's operation before installing the LM10 into the wall. Using the included hardware, install the LM10 into a standard electricians back-box (pattress) (LM10-EU=UK47mm depth single gang, LM10-CU=USAtype J-box 50mm). Important Care should be taken in choosing a site for the LM10, ALWAYS refer to the precautions later in this guide. Bear in mind that any local sources will likely require mains power. [. . . ] However, it is imperative that you always check the wiring regulations in force for your application and area. FACEPLATES The LM10 faceplate system is based on the (LM10-EU=50x50 `easy-clip' module, LM10CU=DecoraTM) standard and is interchangeable for the wide range of faceplates made by manufacturers such as (LM10-EU=MK Electric, RPP etc, LM10-CU=Leviton etc) that conform to this standard. If it is desired to fit another faceplate, it can be replaced by gently prising apart the LM10 faceplate and snapping on another in its place. WIRING GUIDE: EIA/TIA 568A WIRING STANDARD brown white/brown orange white/blue blue white/orange green white/green View from contact end Gather pairs, trim and insert into RJ45 plug Crimp wires securely in place Incognito LM10 7 CAT-5 CONNECTIONS A Cat-5 cable is used to connect the LM10 to a keypad output on an AH10 hub and to a KP10 amplified control module. Use Cat-5 cables (use EIA/TIA 568A RJ-45 wire configuration, see page 7) to connect from the hub to a LM10 wall plate (optional), and then wire from the wall plate to the KP10 (see opposite diagrams). The LM10 has punchdown connectors for the eight individual conductors of the Cat-5 cable, use a punchdown tool (LM10-EU=Krone, LM10-CU=110+ blade) to insert conductors. If using shielded Cat-5 cable, connect the shields to the green terminal blocks as shown in the opposite diagrams (dotted lines). Note: When wiring directly to the LM10, crimp on a male RJ-45 connector using the EIA/TIA 568A RJ-45 wire configuration (see Wiring Guide: EIA/TIA 568A wiring standard on page 7) for connection to the hub. Single local audio source Connect the LM10 as shown in the diagrams. Switch over SW1 (LC1) to the ON position and SW2 (LC2) to the OFF position. The LM10 will respond to the Local 1 remote command when selected. 8 Incognito LM10 Incognito LM10 AH10 Hub LM10 Rear OUT KP10 Speaker Cable IN CAT-5 OUT CAT-5 IN MAIN ZONE EU version SW1 SW2 AH10 Hub LM10 Rear OUT KP10 Speaker Cable IN CAT-5 OUT CAT-5 SW2 SW1 IN MAIN ZONE CU version Incognito LM10 9 CAT-5 CONNECTIONS CONTINUED It is possible to add up to two LM10 units per main zone. This gives you the option to listen to either one by selection from the keypad or LR10 remote control (Local1/Local 2). The module needs to be told whether there are one or two LM10's present. Dual LM10s fitted in a single zone Connect the LM10s as shown in the opposite diagrams. Local Source 1 ­ Switch over SW1 (LC1) to the ON position and SW2 (LC2) to the OFF position. Local Source 2 ­ Switch over SW1 (LC1) to the OFF position and SW2 (LC2) to the ON position. Note: If using an LR10 to select the local source, this will ONLY select Local 1 as default. 10 Incognito LM10 Incognito LM10 AH10 Hub Local Source 1 OUT Local Source 2 OUT KP10 Speaker Cable IN OUT OUT IN CAT-5 CAT-5 CAT-5 IN IN EU version SW1 SW2 SW1 SW2 MAIN ZONE AH10 Hub Local Source 1 OUT Local Source 2 OUT KP10 Speaker Cable IN IN CAT-5 OUT OUT CAT-5 SW2 SW2 IN IN MAIN ZONE CU version SW1 SW1 CAT-5 Incognito LM10 11 CAT-5 CONNECTIONS CONTINUED Single LM10 with main and sub-zone fitted Connect the LM10 as shown in the diagrams. Switch over SW1 (LC1) to the ON position and SW2 (LC2) to the OFF position. The LM10 will respond to the Local 1 remote command when selected. EU version AH10 Hub Local Source 1 OUT SUB-ZONE KP10 Speaker Cable CAT-5 IN CAT-5 OUT MAIN ZONE KP10 Speaker Cable CAT-5 CAT-5 IN SW1 SW2 12 Incognito LM10 Incognito LM10 CU version AH10 Hub Local Source 1 OUT SUB-ZONE KP10 Speaker Cable CAT-5 IN CAT-5 MAIN ZONE KP10 CAT-5 SW2 IN OUT CAT-5 Speaker Cable SW1 Incognito LM10 13 CAT-5 CONNECTIONS CONTINUED Dual LM10s with main and sub-zones fitted Connect the LM10s as shown in the diagrams. Local Source 1 ­ Switch over SW1 (LC1) to the ON position and SW2 (LC2) to the OFF position. Local Source 2 ­ Switch over SW1 (LC1) to the OFF position and SW2 (LC2) to the ON position. Note: If using an LR10 to select the local source, this will ONLY select Local 1 as default. AH10 Hub Local Source 1 OUT Local Source 2 CAT-5 OUT CAT-5 IN OUT OUT IN CAT-5 SUB-ZONE KP10 CAT-5 CAT-5 IN IN CAT-5 SW1 SW2 MAIN ZONE KP10 EU version AH10 Hub SW1 SW2 Local Source 1 OUT Local Source 2 OUT SUB-ZONE KP10 CAT-5 CAT-5 IN CAT-5 IN CAT-5 SW2 OUT OUT CAT-5 SW2 IN IN MAIN ZONE KP10 SW1 SW1 CAT-5 CU version 14 Incognito LM10 Incognito LM10 SOURCE ROTATE FOR LOCAL 1&2 ON THE KEYPAD Note: This feature is only available if the KP10 is part of a full Incognito multi-room system with one or two Local Input Modules (LM10) fitted. [. . . ] Adjust levels as required using a small trimmer. Turning the gain level pots clockwise increases the audio level and anti -clockwise decreases it. R ­ Local gain L ­ Local gain R ­ Local gain L ­ Local gain LM10 LM10 EU version CU version The LM10 also has a local infra-red (IR) output allowing for local source equipment to be controlled via an IR1. This will only pass through remote source or commands once the local source has been selected (Local 1 or Local 2) from the LR10 remote or KP10 keypad. Having selected the local source, you will be able to listen to whatever source has been connected to the R/L phono sockets on the LM10. Incognito LM10 17 LIMITED WARRANTY Cambridge Audio warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below). [. . . ]